Retired - Ocean Mist Stacking Bracelet Set

PROJECT B613
Designer: Julie Bean
Skill Level: Beginner
The color of the water in the tropics, these glass teardrop stacking bracelets are a breath of fresh air. With the look of complicated wire wrapping but without the difficulty, these are fun and easy to make.
Instructions

Note: Components and tools listed within this INSTRUCTIONS box and the printer-friendly PDF, if available, may have been discontinued since this project was published. Refer to the PURCHASE COMPONENTS and TOOLS AND OTHER SUPPLIES sections for current availability.

  1. If you would like to see a step by step video tutorial on this project, see this video.
  2. This project provides enough materials to make two of these bracelets so that they can stack on your wrist. To make the second bracelet, just repeat the directions below.
  3. Begin by cutting a 12 inch piece of 22 gauge silver color craft wire. About an inch from the end, create a wrapped wire loop and trim the excess wire (from the 1 inch part) with flush cutters.
  4. String onto your wire: 1 Czech glass 8mm glass teardrop in alexandrite, 1 Czech glass 8mm glass teardrop in light teal. Repeat this pattern going back and forth between the two colors until you have 20 of each color beaded onto your wire. This will make for a 7" bracelet. If your wrist is a little wider, add a few extra beads at this time.
  5. Straighten out the beads so that all the teal beads are on one side and alexandrite on the other side. Push the beads together so they are quite snug. Create another wrapped wire loop at the end and trim off excess wire with flush cutters.
  6. Cut an 18 inch length of 26 gauge silver toned craft wire. Starting on one end of your bracelet, wrap the tail end of the 26 gauge wire length 3 times around the base of the wrapped wire loop at the end. Now review the video tutorial on this bracelet to see how to wrap the wire up and around and in between the glass teardrops. When you get to the other end of the bracelet, wrap the wire 3 times around the base of the wrapped wire loop.
  7. Open a 4mm jump ring and link onto it the hoop at the base of your lobster clasp. Next, link this same jump ring to the wrapped wire loop on one end of your bracelet. Close the jump ring.
  8. Open an 8mm jump ring. Link it to the the wrapped wire loop on the opposite end of your bracelet which you just added the clasp to. Close the jump ring.
  9. The final step it to take your bracelet and shape the wire so that it is a round shape, mimicking your wrist. Once this is done, you are all finished.
WHAT YOU'LL NEED: (scroll down for purchase options)
  • BCP-09101 -
    Project uses 40 pieces. You will need 1 package.

  • BCP-09160 -
    Project uses 40 pieces. You will need 1 package.

  • FJR-1122 - Antiqued Silver Plated Open Jump Rings 8mm (25)
    Project uses 1 piece. You will need 1 package.

  • FCL-2527 - Antiqued Silver Plated Sleek Lobster Claw Clasps 12mm (6)
    Project uses 2 pieces. You will need 1 package.

  • FJR-3092 - Antiqued Silver Plated Open Jump Rings 4mm 21 Gauge (50)
    Project uses 1 piece. You will need 1 package.

  • WNT-2630 - Beadsmith Tarnish Resistant Silver Color Copper Wire 26 Gauge 34 Yards (31 Meters)
    Project uses 18 pieces. You will need 1 package.

  • WNT-2230 - Beadsmith Tarnish Resistant Silver Color Copper Wire 22 Gauge 20 Yards (18.2 Meters)
    Project uses 12 inches. You will need 1 package.

RECOMMENDED TOOLS:
  • XTL-5514 - Beadsmith Jewelry Fine Round Nose Micro Pliers
  • XTL-5511 - Beadsmith Jeweller's Micro Pliers Chain Nose Flat Nose
  • XTL-5600 - Xuron Sharp Flush Cutter Pliers - Wire/Soft Flex
Additional Information
Ingredients FJR-1122, FCL-2527, FJR-3092, WNT-2630, WNT-2230,

Purchase Components

Purchase the components needed to make this project. Change quantities as needed to make multiple pieces. This project is RETIRED. Please review project instructions carefully—some items may no longer be available for this project and will not be listed below. Tip: Save this project to your wishlist to easily return to project instructions.
Antiqued Silver Plated Open Jump Rings 8mm (25 pcs)
You will need 1 package(s).
1 package = 25 Pieces.
$1.49 / Package | SKU: FJR-1122
Lobster Clasps, Curve 12mm, Antiqued Silver Plated (6 Pieces)
You will need 1 package(s).
1 package = 6 Pieces.
$4.64 / Package | SKU: FCL-2527
Antiqued Silver Plated Open Jump Rings 4.5mm 21 Gauge (50 Pieces)
You will need 1 package(s).
1 package = 50 Pieces.
$1.49 / Package | SKU: FJR-3092
Wire Elements, Tarnish Resistant Silver Color Copper Wire, 26 Gauge 34 Yards (31 Meters)
You will need 1 package(s).
1 package = 1 Spool.
$9.75 / Package | SKU: WNT-2630
Wire Elements, Tarnish Resistant Silver Color Copper Wire, 22 Gauge 20 Yards (18.2 Meters)
You will need 1 package(s).
1 package = 1 Spool.
$10.95 / Package | SKU: WNT-2230
Earn Reward Points Earn Reward Points with your purchase of project components or tools.

Tools and Other Supplies:

The Beadsmith Jewelry Fine Round Nose Micro Pliers
$6.49 / Package | SKU: XTL-5514
The Beadsmith Jeweller's Micro Pliers Chain Nose Flat Nose

Related Video [VIEW ALL VIDEOS]

Accessible Options For closed captions/subtitles, click the CC icon on the video player after starting the video.

You recently viewed

Clear recently viewed