Note: Components and tools listed within this INSTRUCTIONS box and the printer-friendly PDF, if available,
may have been discontinued since this project was published. Refer to the PURCHASE COMPONENTS and TOOLS AND
OTHER SUPPLIES sections for current availability.
This wrap bracelet is approximately seven inches around (each wrap). To adjust the finished size of your bracelet, multiply the amount to increase or decrease by three and adjust the length of the cord accordingly.
- You can see this bracelet made start to finish in the video How to Make the Wrapped in Love Bracelet.
- Cut a length of synthetic rubber cord that is 24" long.
- Thread the end of the cord through the smallest opening on the Tribuckle (ridge side up) and fold over the last 3/4".
- Set the hole punch for a 2mm hole. Use the punch to make a hole through both folded layers of cork about 1/2" from the folded edge.
- Thread a washer onto one of the longer eyelets and then insert the washer through the holes from the top. Thread a second washer onto the back of the eyelet.
- Place the assembly flange side down onto the anvil, set eyelet setter into the tube, and tap gently with a hammer while rotating the setter at a slight angle until the eyelet is set.
- Use a pencil to mark the placement for your 10 eyelets, about 2" apart along the bracelet, leaving the final 3" blank.
- Set your hole punch for 2mm holes and punch a hole at each pencil mark.
- Insert one of the shorter eyelets into one of the holes and set as before. Repeat with the remaining shorter eyelets to set all ten.
- Thread your red bead onto a head pin and create a simple wire loop.
- Open a jump ring and place the wire loop onto it. Thread it through the bottom opening of the Tribuckle and close the ring. Repeat this process to hang the winged heart charm next to the bead dangle.
WHAT YOU'LL NEED: (scroll down for purchase options)
- XCR-8006 - Synthetic Rubber Cord, Flat 10x1.9mm, 1 Meter, Black
Project uses 24 inches. You will need 1 package.
- FCL-9381 - TierraCast Antiqued Lead-Free Pewter Tribuckle Connector Clasp 1/2 Inch - 1 Piece
Project uses 1 piece. You will need 1 package.
- PND-5341 - TierraCast Fine Silver Plated Pewter Winged Heart Charm 17.5mm (1)
Project uses 1 piece. You will need 1 package.
- PND-12001 - TierraCast Black Finish Brass Micro Washer For Jewelry 6mm - 10 Pieces
Project uses 2 pieces. You will need 1 package.
- FCO-4805 - TierraCast Silver Plated Brass Hollow Eyelets 3.8mm Diameter, 7mm Long - Pack of 10
Project uses 1 piece. You will need 1 package.
- FCO-4799 - TierraCast TierraCast Silver Plated Brass Hollow Eyelets 3.7mm Diameter, 5.2mm Long - Pack of 10
Project uses 10 pieces. You will need 1 package.
- FJR-5415 - TierraCast Fine Silver Plated Brass Open Jump Rings 7.7mm 16 Gauge (25)
Project uses 2 pieces. You will need 1 package.
- FHP-5325 - Silver Plated Head Pins 2 Inches/21 Gauge (X50)
Project uses 1 piece. You will need 1 package.
- BCP-21004 - Czech Glass Round Party Beads 10mm - Dark Red (1 Strand / 18 Beads)
Project uses 1 piece. You will need 1 package.
RECOMMENDED TOOLS:- XTL-5511 - Beadsmith Jeweller's Micro Pliers Chain Nose Flat Nose
- XTL-5514 - Beadsmith Jewelry Fine Round Nose Micro Pliers
- XTL-5600 - Xuron Sharp Flush Cutter Pliers - Wire/Soft Flex
- XTL-0785 - TierraCast Eyelet Setter And Anvil Tool - 1 Tool
- XTL-5502 - BeadSmith Rotating Leather Hole Punch Tool - Creates 6 Hole Sizes!
- XTL-5500 - Cord Cutter Tool For Regaliz Cord 3 Inches Long
- XTL-0248 - Eurotool Brass Mallet For Metal Smithing - 1 Pound
For closed captions/subtitles, click the CC icon on the video player after starting the video.
Earn Reward Points with your purchase of project components or tools.
