Retired - Tied Up in Love Bracelet

PROJECT B1002
Designer: Megan Milliken
Skill Level: Intermediate
A shambhala style bracelet made with elegant silk string and Austrian crystals gives you a new way to wear Pandora style beads. Dress it up or down for any romantic occasion!
Instructions

Note: Components and tools listed within this INSTRUCTIONS box and the printer-friendly PDF, if available, may have been discontinued since this project was published. Refer to the PURCHASE COMPONENTS and TOOLS AND OTHER SUPPLIES sections for current availability.

These instructions will make a bracelet that adjusts to approximately 7-8". You can add or subtract beads to change the length of the bracelet. Each extra bead will add approximately 3/4".
  1. Begin by folding one strand of 2 mm red silk fabric string in half. Line up the ends of the other two strands with the folded end of the doubled strand and tie the three pieces in an overhand knot about 4" from the end. You should have two short and two long strands hanging below the knot.
  2. Tie two macrame square knots. All of the macrame knots will be tied onto the shorter strands using the longer strands.
  3. Thread a silver tone pink enamel and Austrian crystal crystal Pandora style bead onto the shorter strands. Bring the outside strands across the bead to either side and tie two macrame square knots after the bead.
  4. Repeat step 3 with a 4.5 mm crystal colored Austrian crystal crystal BeCharmed briolette bead.
  5. Continue to add beads, alternating between the enamel beads and the briolette beads, with two macrame square knots between each bead, until you've used all seven beads. End with two macrame square knots after the last enamel bead.
  6. Finish the end of the last macrame knot with a square knot that is glued in place using a small amount of E6000 glue. Allow the glue to dry for at least an hour before moving on. Trim the ends of the string and finish with a bit of E6000 glue. Do not trim the shorter strands that run down the middle. Let the glue dry for at least an hour before moving on. Save one of the strands that is trimmed off to make the sliding knot clasp later.
  7. Untie the overhand knot you made at the beginning of the bracelet. Finish this end of the knotting in the same manner as the first, allowing the glue to dry for at least an hour before moving on.
  8. Bring the ends of the bracelet around into a loop, crossing over the loose center strands for a few inches. Use the trimmed off strand to tie a sliding knot clasp with four macrame square knots onto the bracelet.
  9. Finish the sliding knot in the same manner as the ends of the bracelet knotting, allowing the glue to dry for at least an hour before moving on.
  10. Adjust the sliding knot to sit about an inch from the bracelet knotting on either side. Tie the ends of the excess string into an overhand knot about 2" from each side of the sliding knot. Check to make sure that the bracelet adjusts to fit over your hand. If the fit is good, trim the ends of the string after the overhand knots. Apply a dab of E6000 glue to the tips to keep the string from fraying.
  11. When you've finished, allow all of the glue to dry for 24 hours before wearing.
WHAT YOU'LL NEED: (scroll down for purchase options)
  • XCR-46008 -
    Project uses 3 pieces. You will need 3 packages.

  • SWBB-5050 - Austrian Crystal, 5948 BeCharmed Briolette European Style Lg Hole Bead 14mm, 1 Pc, Crystal
    Project uses 3 pieces. You will need 3 packages.

  • BMB-8316 - Silver Tone Large Hole Lt Pink Enamel Bead Adorned With Austrian crystals (1)
    Project uses 4 pieces. You will need 4 packages.

  • XTL-1054 - E6000 Industrial Strength Glue Adhesive (0.18 fl oz)
    Project uses 1 piece. You will need 1 package.

RECOMMENDED TOOLS:
  • XTL-5700 - Fiskars 5 Precision Tip Scissors - Super Sharp
Additional Information
Theme Valentine's Day
Ingredients XTL-1054,

Purchase Components

Purchase the components needed to make this project. Change quantities as needed to make multiple pieces. This project is RETIRED. Please review project instructions carefully—some items may no longer be available for this project and will not be listed below. Tip: Save this project to your wishlist to easily return to project instructions.
E6000 Industrial Strength Glue Adhesive (0.18 fl oz)
You will need 1 package(s).
1 package = 1 Piece.
$2.19 / Package | SKU: XTL-1054
Earn Reward Points Earn Reward Points with your purchase of project components or tools.

Tools and Other Supplies:

/ Package | SKU: XTL-5700

Related Video [VIEW ALL VIDEOS]

Accessible Options For closed captions/subtitles, click the CC icon on the video player after starting the video.

You recently viewed

Clear recently viewed