Retired - Delia Necklace

Note: Components and tools listed within this INSTRUCTIONS box and the printer-friendly PDF, if available, may have been discontinued since this project was published. Refer to the PURCHASE COMPONENTS and TOOLS AND OTHER SUPPLIES sections for current availability.

1. Using your flush cutters, cut 2 lengths of chain, one at 20� and the other at 25�. Set aside.
2. Gather 19 Amethyst and Lime Vitrail Rizo beads. I used 5 Amethyst beads and 14 Lime Vitrail beads, but you can use a different combination if you'd like. Also gather 19 4mm jump rings.
3. Lay your shorter 20� chain onto your work space. Your chain is made up of smaller and larger links. You will be attaching Rizo beads onto the smaller links on your chain using open jump rings.
4. Find the center 10" mark of your 20� chain.
5. Open a 4mm jump ring with your chain nose pliers and slide on a Rizo bead, then slide your jump ring onto a smaller link in the center 10" point of your chain length. Close the jump ring.
6. Repeat the process of attaching 9 more Rizo beads using open jump rings onto the smaller links of your chain, at either side of the Rizo bead you just attached. Close the jump rings back up. Set your chain aside for now.
7. Next, take your Vintaj Natural Brass Diamond Trellis Filigree Stamping and using your Eurotool EuroPunch, punch a hole at the tip of one side of the stamping. (You will be attaching a jump ring through this hole). See photo.
8. With your pliers, open up a 4mm jump ring and and slide it onto the small chain link that is at the 12.5" mark of your 25" long chain. Before closing, also slide on a larger 7mm jump ring. Close the 4mm jump ring.
9. Open up the 7mm jump ring and slide on your stamping, through the hole you just punched and close.
10. Next, watch the video on How to Use Vintaj Patinas and Glaze. .
11. Take your Vintaj Natural Brass Diamond Trellis Filigree Stamping and using your paint brush, add a thin layer of Vintaj Patina in Moss Green. While the patina is still wet, use the side of your Vintaj Relief Block Vintaj Relief Block to sand the raised areas of your stamping to show off the detail. Wait a few minutes for your stamping to dry.
12. Watch the video on How to Use a Magical Pick.
13. Once your stamping is dry, take your Hypo Cement glue and using the applicator tip, add 12 tiny dabs of glue throughout your stamping. Refer to the photo for placement assistance.
14. Following what you learned in the video, use your Magical Pick to pick up each Austrian crystal rhinestone flatback in Hematite and place it flat side down onto the glue.
15. Wait a few minutes for your stamping to dry.
16. Next, open up a 4mm jump ring with your pliers and slide on the last link from one side of both your lengths of chain. Close the jump ring.
17. Open up another jump ring and slide on the last links from the 2 sides of chain from the other side.
18. Also slide on the loop from your lobster clasp and close.
19. Enjoy!

• CHA-99894 - Vintaj Natural Brass 3x6mm Fine Wire Oval Long Short Chain - Sold By The Foot
  Project uses 45 inches. You will need 4 packages.


• BCR-068 - Rizo Czech Glass Drop Seed Beads 6x2.5mm - Lime Vitrail Matted 10 Grams
  Project uses 14 pieces. You will need 1 package.


• BCR-037 - Rizo Czech Glass Drop Seed Beads 6x2.5mm - Amethyst 10 Grams
  Project uses 5 pieces. You will need 1 package.


• PND-7015 - Vintaj Natural Brass Diamond Trellis Filigree Stamping 64x21mm (1)
  Project uses 1 piece. You will need 1 package.


• XTL-9067 - Vintaj Patina Opaque Permanent Ink - Moss Green - 0.5 Ounce Bottle
  Project uses 1 piece. You will need 1 package.


• SWF-40915 - Austrian Crystal, Round Flatback Rhinestone SS9 2.5mm, 72 Pieces, Hematite
  Project uses 12 pieces. You will need 1 package.


• FJR-5450 - Antiqued Brass Open Jump Rings 4mm 22 Gauge (x100)
  Project uses 22 pieces. You will need 1 package.


• FJR-5179 - Antiqued Brass Open Jump Rings 7mm 18 Gauge (50)
  Project uses 1 piece. You will need 1 package.


• XTL-1001 - G S Hypo Cement Precise Applicator Essential!
  Project uses 1 piece. You will need 1 package.


• FCL-2400 - Antiqued Brass Curved Lobster Clasps 8mm (6)
  Project uses 1 piece. You will need 1 package.

• XTL-4004 - Beadsmith Magical Rhinestone Pick Up Tool With Cleaning Kit - Great For Placing Flatback Rhinestones
• XTL-5600 - Xuron Sharp Flush Cutter Pliers - Wire/Soft Flex
• XTL-5511 - Beadsmith Jeweller's Micro Pliers Chain Nose Flat Nose
• XTL-2222 - Vintaj Metal Relief Block For Filing, Buffing & Sanding
• XTL-0060 - Eurotool EuroPunch 1.25mm Round Hole Punch Pliers For Sheet Metal