Note: Components and tools listed within this INSTRUCTIONS box and the printer-friendly PDF, if available, may have been discontinued since
this project was published. Refer to the PURCHASE COMPONENTS and TOOLS AND OTHER SUPPLIES sections for current availability.
For this project you will be stringing 3 strands of beading wire at the same time! As you string your beads, please refer to the photo and adjust your stringing tension as needed so that the beaded strands are spaced nicely in your necklace.
- Cut three strands of beading wire, 30 inches long each. Place all three strands into a Bead Buddy. Please leave 6-inch tails sticking out the back of the Bead Buddy.
- Now string onto all three strands 1 crimp tube, two 6mm bicones, 1 metal rondelle bead, and one 6mm bicone.
- Separate out your strands and onto each of the three strands string: four 3mm bicones, three 4mm bicones, two 6mm bicones, three 4mm bicones, and four 3mm bicones. Now bring all three strands together and feed them all through one 6mm bicone, 1 metal rondelle bead, and 1 more 6mm bicone. Please see photo for reference.
- Repeat the previous step 5 more times BUT make sure that when you get to the middle of the necklace, you add a metal spacer bail instead of the metal rondelle. It will be after you have a total of three beaded segments (please see photo for reference).
- At this point you should have your main beading completed and the end of the beading wires should be sticking out a 6mm bicone. Add one more 6mm bicone and a crimp tube.
- Loop all three beading wires through the loop on the side of one half of your magnetic clasp. Bring them back around and down through the crimp tube. Crimp your crimp tube, just like you would crimp a crimp tube with just one strand through it (the technique doesn't change just because you have three strands).
- Go to the other side of your necklace, remove the Bead Buddy, and crimp your crimp bead on this end, the same way you did in the previous step.
- Place crimp bead covers over your crimp tubes. To see how to do this, please refer to the video: How to Use Crimp Covers.
- Place a small dab of glue into your bezel setting. Place your fancy stone pear pendant into the glue. Let dry.
- Once dry, open a jump ring and connect it to the loop at the top of the pear pendant and also the loop attached to the bail which is strung onto your necklace already. Close the jump ring.
- Enjoy wearing this spectacular necklace!
WHAT YOU'LL NEED: (scroll down for purchase options)
- PRES-4320-MAG18 - PRESTIGE Crystal, #4320 Pear Fancy Stone 18x13mm, Majestic Green (1 Piece)
Project uses 1 piece(s). You will need 1 package(s).
- PRES-5328-MAG3 - PRESTIGE Crystal, #5328 Bicone Bead 3mm, Majestic Green (1 Piece)
Project uses 144 piece(s). You will need 144 package(s).
- PRES-5328-MAG4 - PRESTIGE Crystal, #5328 Bicone Bead 4mm, Majestic Green (1 Piece)
Project uses 108 piece(s). You will need 108 package(s).
- PRES-5328-MAG6 - PRESTIGE Crystal, #5328 Bicone Bead 6mm, Majestic Green (1 Piece)
Project uses 52 piece(s). You will need 52 package(s).
- BMB-0097 - Metal Bead, Hammertone Rondelle 3.5x7mm, Bright Gold, by TierraCast (2 Pieces)
Project uses 6 piece(s). You will need 3 package(s).
- FCL-6844 - TierraCast Magnetic Clasps, Hammertone 9x18mm, Bright Gold Plated (1 Set)
Project uses 1 piece(s). You will need 1 package(s).
- PNT-126 - TierraCast Bezel Pendant, Fits #4320 Pear 18x13mm, Gold Plated (1 Piece)
Project uses 1 piece(s). You will need 1 package(s).
- BMB-906 - TierraCast Spacer Bail, Hammered with Loop 3x12mm, Bright Gold Plated (2 Pieces)
Project uses 1 piece(s). You will need 1 package(s).
- FJR-5465 - 22K Gold Plated Open Jump Rings 6mm 21 Gauge (50 pcs)
Project uses 1 piece(s). You will need 1 package(s).
- XCR-5143 - Soft Flex, 21 Strand Fine Beading Wire .014 Inch Thick, Satin Silver (30 Feet)
Project uses 90 inches. You will need 1 package(s).
- XTL-1054 - E6000 Industrial Strength Glue Adhesive (0.18 fl oz)
Project uses 1 piece(s). You will need 1 package(s).
- FCR-9018 - Crimp Bead Covers, 4mm, Gold Plated (50 Pieces)
Project uses 2 piece(s). You will need 1 package(s).
- FCR-01133 - Crimp Beads, 3x3mm, Sterling Silver (10 Pieces)
Project uses 2 piece(s). You will need 1 package(s).
RECOMMENDED TOOLS:
- XTL-5032 - The Beadsmith Wire Looping Pliers - Concave And Round Nose
- XTL-5450 - Xuron Jeweler's Super Fine Pliers Chain Nose Flat Nose
- XTL-5600 - Sharp Flush Cutter Pliers - For Cutting Beading Wire (1 Piece)
- XTL-113 - Bead Buddy, Bead Bugs Bead Stoppers Combo Pack Mini + Regular (8 Pieces)
- XTL-0020 - Baby Wubbers Quality Fine Chain Nose Jeweller's Pliers
- XTL-5265 - Mighty Crimping Pliers Large Crimpers For 3mm Crimps