Retired - Regaliz Dragonfly Two-tone Bracelet

Note: Components and tools listed within this INSTRUCTIONS box and the printer-friendly PDF, if available, may have been discontinued since this project was published. Refer to the PURCHASE COMPONENTS and TOOLS AND OTHER SUPPLIES sections for current availability.

1. To make this bracelet please watch our video: How use the Charm Holder Connector for Rubber Regaliz.
2. The center of the connector bar measures 7mm (just over 1/4"). You will need to subtract this from your overall length of your bracelet. Also the recesses of the clasp measure 5mm at each end for a total of 10mm (3/8").
3. For a 7 1/2" bracelet, cut each piece of rubber to 3 3/4". Make sure both cords are exactly even and your cuts are perpendicular other wise it will not sit correctly.
4. Open one jump ring and attach the dragonfly charm to the charm holder connector bar.
5. Before you glue anything, test your length. Place one end of the rubber on to the bar, then slide on one slider bead and one rubber o-ring. Repeat with the other side.
6. Place both ends into the clasp ends. You can carefully measure this on a mandrel or your wrist. If you need to cut any rubber, do so now evenly on both sides.
7. Once you have your desired size, carefully remove the clasp and slide back your beads and o-rings. As demonstrated in the video, place a dab of super new glue into the recess of the cord and place one end of the rubber cord onto the connector bar. Repeat with the other side.
8. Slide your beads and rubber o-rings back into place.
9. Place a dab of super new glue into the recess on one side of your clasp and slip one end of the cord into the recess. Allow to dry.
10. Repeat the previous step on the other side of your bracelet.
11. Allow all glue to dry thoroughly before wearing.

• FCO-9303 - Antiqued Brass Plated Charm Holder Connector For Rubber Regaliz 10mm Cord - 1 Piece
  Project uses 1 piece. You will need 1 package.


• BMB-9938 - Antiqued Brass Plated Spacer With Textured Lines For Regaliz 10mm Rubber Cord - 1 Piece
  Project uses 2 pieces. You will need 2 packages.


• PND-7700 - TierraCast Brass Oxide Finish Pewter Dragonfly Charm 21mm (1)
  Project uses 1 piece. You will need 1 package.


• FJR-5471 - Antiqued Brass Open Jump Rings 5mm 20 Gauge (x100)
  Project uses 1 piece. You will need 1 package.


• FRC-071 - Rubber O-Ring Jump Ring Spacers Fits Regaliz 12mm Diameter - Chocolate (10)
  Project uses 2 pieces. You will need 1 package.


• FCL-1603 - Antiqued Brass Plated Curved Magnetic Clasp/Cord Ends For Regaliz 10mm Rubber Cord
  Project uses 1 piece. You will need 1 package.


• CHX-1106 - Regaliz Corduroy Rubber Cord 10x6.5mm - Beige (Sold By The Inch)
  Project uses 5 pieces. You will need 5 packages.


• CHX-1107 - Regaliz Corduroy Rubber Cord 10x6.5mm - Sage Green (Sold By The Inch)
  Project uses 5 pieces. You will need 5 packages.


• XTL-1059 - Eurotool Super New Glue - Heavy Duty Adhesive - 3 Gram Bottle
  Project uses 1 piece. You will need 1 package.

• XTL-5511 - Beadsmith Jeweller's Micro Pliers Chain Nose Flat Nose
• XTL-5511 - Beadsmith Jeweller's Micro Pliers Chain Nose Flat Nose
• XTL-5500 - Cord Cutter Tool For Regaliz Cord 3 Inches Long