Note: Components and tools listed within this INSTRUCTIONS box and the printer-friendly PDF, if available, may have been discontinued since
this project was published. Refer to the PURCHASE COMPONENTS and TOOLS AND OTHER SUPPLIES sections for current availability.
This necklace measures 24 inches. To adjust the length simply modify the length of chain used.
- Please watch our video: How to Make a Beaded Wire Flower in a Glass Bottle. Using a similar technique as you learned in the video, cut off about 8 inches of green wire. For this project you will not be adding beads. Fold the wire in half. Make a wire coil loop at the top. This loop will be caught in the top of the rose, holding it in place. String both ends of the wire through the rose. You may want to carefully bend back the inner petals of the rose. Once the loop is in place bend them back into place.
- Once you have the rose in place. Twist the two pieces of wire together until you have about a 1/2 inch, then take one wire and pull it away from the center with your chain nose pliers to create a petal. Then bring the wires back together to twist one more time. Repeat to create one more petal.
- Twist until you have reached the bottom. Your rose should stand about one inch tall. When you have come to the bottom take the two tails of wire and coil them into a base. They should look like a yin yang twist. This will be covered by the crystal clay so it doesn't need to be clean.
- For this next step please watch our video: How to Use Crystal Clay. Mix up equal parts A and B, about the size of a gumball and place it around the base of the flower. Make sure you have it centered as you work around it.
- Once you have the rose in place in the crystal clay, dust the top of the clay with the sparkle dust to coat evenly. Press the dust into the clay. You may use your finger or a paint brush for this step, however be careful not to leave brush marks in your clay. Brush off any excess carefully.
- Take the dome and place it over the top of the rose and carefully squish it into the clay.
- Carefully add a dab of glue to the pendant cap and place on to the top of the dome. Make sure that your loop is facing forward so that when you attach the chain your necklace will hang in the correct direction.
- Once you have let your piece dry for 24 hours, open one 7mm jump ring and attach it to the dome cap. Close the jump ring.
- String the chain through the jump ring.
- Open the jump ring attached to the clasp and attach it to one side of the chain. Close the jump ring. Close the clasp and you're all done!
This flower is built very organically. Please use the above wire wrapping instructions as a guide to create your own design.
WHAT YOU'LL NEED: (scroll down for purchase options)
- BGL-01000 - Hollow Glass Dome for Jewelry, 24.5x36.5mm Pill Shape, 2 Pieces
Project uses 1 piece. You will need 1 package.
- FLW-0036 - Metal Embellishments, Rose Flower Beads 12mm, 20 Pieces, Matte Red
Project uses 1 piece. You will need 1 package.
- WCR-2413 - Artistic Wire, Silver Plated Craft Wire 24 Gauge Thick, 10 Yard Spool, Christmas Green
Project uses 8 Inches. You will need 1 package.
- PND-07000 - Bezel Pendant Base, Round No Loop 25mm, 4 Pieces, Antiqued Brass
Project uses 1 piece. You will need 1 package.
- PND-07002 - Pendant Cap End with Loop, Round 7x8mm, 4 Pieces, Antiqued Brass
Project uses 1 piece. You will need 1 package.
- XTL-1161 - Crystal Clay Sparkle Dust - Mica Powder 'White Pearl' 1.5g
Project uses 1 piece. You will need 1 package.
- TRC-251 - Crystal Clay 2-Part Epoxy Clay Kit 'White' 25 Grams
Project uses 1 piece. You will need 1 package.
- CHA-9948 - Antiqued Brass Round Rolo Chain 3.7mm Bulk By The Foot
Project uses 2 pieces. You will need 2 packages.
- FJR-5175 - Antiqued Brass Open Jump Rings 7mm 19 Gauge (20)
Project uses 1 piece. You will need 1 package.
- FCL-2607 - Antiqued Brass Sleek Lobster Claw Clasps 10mm (10)
Project uses 1 piece. You will need 1 package.
RECOMMENDED TOOLS:- XTL-5511 - Beadsmith Jeweller's Micro Pliers Chain Nose Flat Nose
- XTL-5514 - Beadsmith Jewelry Fine Round Nose Micro Pliers
- XTL-5600 - Xuron Sharp Flush Cutter Pliers - Wire/Soft Flex