Note: Components and tools listed within this INSTRUCTIONS box and the printer-friendly PDF, if available, may have been discontinued since
this project was published. Refer to the PURCHASE COMPONENTS and TOOLS AND OTHER SUPPLIES sections for current availability.
This necklace measures approximately 17.5 inches. To modify the length, simply adjust the length of chain on both sides respectively.
- Begin by cutting off a length of beading wire, 24 inches in length. Place a bead stopper at one end.
- String on the beads in the following order: one 4mm blue pearl, one bead cone, one 6mm coral pearl, and one bead cap.
- Then string on one 8mm blue pearl, one bead cap, one 6mm coral pearl, one bead cap, one 4mm blue pearl, one bead cap, one 6mm coral pearl, and one bead cap. Repeat 13 times.
- Next string on one bead cap, one 6mm coral pearl, one bead cone, and one 4mm blue pearl.
- String on one crimp bead. Thread the wire up through one wire protector and back down the other side and through the crimp tube. Pull snug and crimp the crimp tube. Trim any excess wire. Open one jump ring and attach it to one lobster clasp and to the wire protector. Close the jump ring.
- Move to the other side of the necklace, remove the bead stopper and repeat the above process. This time you will be simply adding one jump ring without adding the lobster clasp.
WHAT YOU'LL NEED: (scroll down for purchase options)
- BMB-7060 - Antiqued Brass Scalloped Flower Bead Caps 6mm (x50)
Project uses 58 pieces. You will need 2 packages.
- SWP-6014 - Austrian Crystal, 5810 Round Faux Pearl Beads 6mm, 50 Pieces, Coral
Project uses 30 pieces. You will need 1 package.
- SWP-8037 - Austrian Crystal, 5810 Round Faux Pearl Beads 8mm, 25 Pieces, Iridescent Dark Blue
Project uses 15 pieces. You will need 1 package.
- SWP-4037 - Austrian Crystal, 5810 Round Faux Pearl Beads 4mm, 50 Pieces, Iridescent Dark Blue
Project uses 16 pieces. You will need 1 package.
- FCR-4144 - Antiqued Brass Wire & Thread Protectors .024 Inch Loops (50)
Project uses 2 pieces. You will need 1 package.
- FCL-4711 - Antiqued Brass Curved Lobster Clasps 12mm (10)
Project uses 1 piece. You will need 1 package.
- FJR-5301 - Antiqued Brass Open Jump Rings 6mm 18 Gauge (x100)
Project uses 2 pieces. You will need 1 package.
- XCR-69863 - Beadalon Wire Metallic Bronze 19 Strand .018 Inch / 30Ft
Project uses 24 Inches. You will need 1 package.
- FCO-1253 - Antiqued Brass Beading Cone / Strand Reducer 12.5x5.5mm (2 Pieces)
Project uses 2 pieces. You will need 1 package.
- FCR-1262 - Antiqued Brass Economy Crimp Beads 3mm x 2.7mm (50)
Project uses 1 piece. You will need 1 package.
RECOMMENDED TOOLS:- XTL-3000 - Bead Stopper- Stop Beads Sliding Off Stringing Material
- XTL-5600 - Sharp Flush Cutter Pliers - For Cutting Beading Wire, 1 Piece
- XTL-5511 - Beadsmith Jeweller's Micro Pliers Chain Nose Flat Nose
- XTL-5608 - Xuron 4 In 1 Crimping Pliers - Works On 1, 2 And 3mm Crimps!