Retired - Chunky Labradorite Ring

PROJECT R7004
Designer: Rachel Zaimont
Skill Level: Advanced
Blue labradorite nuggets glow like river stones in the light of a tiny star that dangles daintily down your finger.
Instructions

Note: Components and tools listed within this INSTRUCTIONS box and the printer-friendly PDF, if available, may have been discontinued since this project was published. Refer to the PURCHASE COMPONENTS and TOOLS AND OTHER SUPPLIES sections for current availability.

In addition to the materials listed above, you will also need a face mask and a pair of disposable gloves to complete this project.
  1. Take six labradorite gemstone nuggets (or however many you want), and arrange them in the bezel of your ring in a configuration you like. Glue them into the bezel using Crafter's Pick.
  2. Take one gold screw eye pin and glue it into the bezel near the bottom edge, so the loop of the eye pin protrudes from the bezel. Wait until the glue dries clear before proceeding with the next steps.
  3. Watch our video on how to use Ice Resin. Put on your disposable gloves and face mask. Based on the instructions in the video, measure your resin and stir with a popsicle stick until all striations are gone. Then it is fully mixed, use the stick to drip the resin into the bezel a few drops at a time (you do not need to fill the bezel, only make sure the stones are captured at the bottom of the bezel).
  4. Allow the resin to cure in a dust-free area for three days.
  5. Once the resin has cured, use pliers to open the jump ring that comes attached to one gold star charm. Slide it through the loop of the screw eye pin at the bottom of the ring bezel. Close the jump ring.
  6. Enjoy your ring!
WHAT YOU'LL NEED: (scroll down for purchase options)
  • SPLA-808 - Labradorite Grade AAA Gemstones, Nuggets 7-11mm, 20 Pieces, Blue Grey
    Project uses 6 pieces. You will need 1 package.

  • FRG-1033 - Nunn Design Deep Bezel Ring, Circle 18mm, 1 Ring, Antiqued Gold
    Project uses 1 piece. You will need 1 package.

  • FCO-8007 - Iron Screw Eye Pin, 5x10mm Open Ring, 20 Pieces, Bright Gold Tone
    Project uses 1 piece. You will need 1 package.

  • PND-6068 - 22K Gold Plated Small Puff Nautical Star Charm - 9x6.5mm (6)
    Project uses 1 piece. You will need 1 package.

  • XTL-1026 - Crafter's Pick The Ultimate Permanent Glue Cement Adhesive 4 OZ
    Project uses 1 piece. You will need 1 package.

  • TRC-10 - ICE Resin Jewelers Grade Clear Casting Epoxy Resin 8 oz Kit
    Project uses 1 piece. You will need 1 package.

RECOMMENDED TOOLS:
  • XTL-5511 - Beadsmith Jeweller's Micro Pliers Chain Nose Flat Nose
  • XTL-5514 - Beadsmith Jewelry Fine Round Nose Micro Pliers
Additional Information
Ingredients XTL-1026, TRC-10,

Purchase Components

Purchase the components needed to make this project. Change quantities as needed to make multiple pieces. This project is RETIRED. Please review project instructions carefully—some items may no longer be available for this project and will not be listed below. Tip: Save this project to your wishlist to easily return to project instructions.
Crafter's Pick The Ultimate Permanent Glue Cement Adhesive 4 OZ
You will need 1 package(s).
1 package = 4 oz..
$8.75 / Package | SKU: XTL-1026
ICE Resin Jewelers Grade Clear Casting Epoxy Resin 8 oz Kit
You will need 1 package(s).
1 package = 8 oz..
$36.69 / Package | SKU: TRC-10
Earn Reward Points Earn Reward Points with your purchase of project components or tools.

Tools and Other Supplies:

The Beadsmith Jeweller's Micro Pliers Chain Nose Flat Nose
The Beadsmith Jewelry Fine Round Nose Micro Pliers
$6.49 / Package | SKU: XTL-5514

Related Video [VIEW ALL VIDEOS]

Accessible Options For closed captions/subtitles, click the CC icon on the video player after starting the video.

You recently viewed

Clear recently viewed