Retired - Butterflies and Birds Bottle Cap Bracelet

PROJECT B608
Designer: Julie Bean
Skill Level: Beginner
Funky and eclectic, this bottle cap bracelet is sure to attract lots of raves. The shiny silver of the bottle cap shows through the colorful bird and butterfly transfers which are overlaid on top.
Instructions

Note: Components and tools listed within this INSTRUCTIONS box and the printer-friendly PDF, if available, may have been discontinued since this project was published. Refer to the PURCHASE COMPONENTS and TOOLS AND OTHER SUPPLIES sections for current availability.

  1. Flatten out 5 bottle caps using a steel bench block and rubber mallet. Using your metal hole punch, punch 2 holes next to each other on one side of each cap, along the "ruffles" and then 2 more holes on the opposite side of the bottle cap. Line the holes up so that they are directly across from each other.
  2. Take your colorful silhouette transfer sheet and cut out 5 images in 1" diameter circles each. I used a 1" metal blank and traced around it to get the exact size. There are also hole punches out there that are this size as well.
  3. Apply the transfer to the bottle cap back. Smooth out any air bubbles with your fingers.
  4. Using a paint brush, paint a layer of Nunn Sealant over the top of the transfers. Let dry.
  5. Line up your bottle caps so that they are in the order you want on the finished bracelet. Line it up so that the holes are next to each other. Open an 8mm jump ring and connect two of the bottle caps together through their side holes. Repeat with all the bottle caps and their holes, connecting them together. Also make sure to put an 8mm jump ring into the holes on the end bottle caps.
  6. Open a 6mm jump ring and link it through the two 8mm jump rings on one side of your bracelet. Also link onto the jump ring the loop at the bottom of your lobster clasp. Close the jump ring.
  7. On the other side of the bracelet, again open a 6mm jump ring and link it to the two already secured 8mm jump rings. Before closing, also link another 8mm jump ring to the 6mm jump ring. Close the jump ring.
WHAT YOU'LL NEED: (scroll down for purchase options)
  • XTL-9544 - Nunn Design Transfer Sheet Colorful Silhouette For Scrapbook -Fits Patera
    Project uses 1 piece. You will need 1 package.

  • PND-2010 - New Silver Crown Bottle Caps Craft Scrapbook Jewelry (50)
    Project uses 5 pieces. You will need 1 package.

  • FJR-1122 - Antiqued Silver Plated Open Jump Rings 8mm (25)
    Project uses 12 pieces. You will need 1 package.

  • FJR-3094 - Antiqued Silver Plated Open Jump Rings 6mm 18 Gauge (50)
    Project uses 1 piece. You will need 1 package.

  • FCL-2527 - Antiqued Silver Plated Sleek Lobster Claw Clasps 12mm (6)
    Project uses 1 piece. You will need 1 package.

  • XTL-1032 - Nunn Design Sealant Protectant 2 oz. - For Patera Findings (1)
    Project uses 1 piece. You will need 1 package.

RECOMMENDED TOOLS:
  • XTL-0060 - Eurotool EuroPunch 1.25mm Round Hole Punch Pliers For Sheet Metal
  • XTL-0258 - Mini Rubber And Steel Bench Block For Metal Working And Wire Hardening
  • XTL-0247 - Eurotool Hammer Rubber Mallet For Metal Smithing - 8 Ounces
  • XTL-5511 - Beadsmith Jeweller's Micro Pliers Chain Nose Flat Nose
Additional Information
Theme Spring
Ingredients FJR-1122, FJR-3094, FCL-2527,

Purchase Components

Purchase the components needed to make this project. Change quantities as needed to make multiple pieces. This project is RETIRED. Please review project instructions carefully—some items may no longer be available for this project and will not be listed below. Tip: Save this project to your wishlist to easily return to project instructions.
Antiqued Silver Plated Open Jump Rings 8mm (25 pcs)
You will need 1 package(s).
1 package = 25 Pieces.
$1.39 / Package | SKU: FJR-1122
Antiqued Silver Plated Open Jump Rings 6mm 18 Gauge, (50 Pieces)
You will need 1 package(s).
1 package = Each.
$2.39 / Package | SKU: FJR-3094
Lobster Clasps, Curve 12mm, Antiqued Silver Plated (6 Pieces)
You will need 1 package(s).
1 package = 6 Pieces.
$4.35 / Package | SKU: FCL-2527
Earn Reward Points Earn Reward Points with your purchase of project components or tools.

Tools and Other Supplies:

Eurotool EuroPunch 1.25mm Round Hole Punch Pliers For Sheet Metal
Eurotool Hammer Rubber Mallet For Metal Smithing - 8 Ounces
The Beadsmith Jeweller's Micro Pliers Chain Nose Flat Nose

Featured New Video [VIEW ALL VIDEOS]

Accessible Options For closed captions/subtitles, click the CC icon on the video player after starting the video.

You recently viewed

Clear recently viewed