Note: Components and tools listed within this INSTRUCTIONS box and the printer-friendly PDF, if available, may have been discontinued since
this project was published. Refer to the PURCHASE COMPONENTS and TOOLS AND OTHER SUPPLIES sections for current availability.
The finished length of this bracelet is roughly eight and one quarter inches long. If you'd like to adjust the length to make it either longer or shorter, you may omit or add 3mm copper beads from either end. Cut a piece of beading wire at ten inches long and secure one end with a Bead Stopper.Onto the wire, thread the following: a 3mm copper bead (BMB-1836)a 5.5mm antique copper fluted beada 3mm copper bead (BMB-1836)three apatite gemstone chips (SPAP-01)a 3mm copper bead (BMB-1836)a 5.5mm antique copper fluted beada 3mm copper bead (BMB-1836)a large red agate nugget (SPAG-53)a 3mm copper bead (BMB-1836)a 5.5mm antique copper fluted beada 3mm copper bead (BMB-1836)three apatite gemstone chips (SPAP-01)a 3mm copper bead (BMB-1836)a 5.5mm antique copper fluted beada 3mm copper bead (BMB-1836)a large red agate nugget (SPAG-53)a 3mm copper bead (BMB-1836)a 5.5mm antique copper fluted beada 3mm copper bead (BMB-1836)three apatite gemstone chips (SPAP-01)a 3mm copper bead (BMB-1836)a 5.5mm antique copper fluted beada 3mm copper bead (BMB-1836)a large red agate nugget (SPAG-53)a 3mm copper bead (BMB-1836)a 5.5mm antique copper fluted beada 3mm copper bead (BMB-1836)three apatite gemstone chips (SPAP-01)a 3mm copper bead (BMB-1836)a 5.5mm antique copper fluted beada 3mm copper bead (BMB-1836)a large red agate nugget (SPAG-53)a 3mm copper bead (BMB-1836)a 5.5mm antique copper fluted beada 3mm copper bead (BMB-1836)three apatite gemstone chips (SPAP-01)a 3mm copper bead (BMB-1836)a 5.5mm antique copper fluted beada 3mm copper bead (BMB-1836)Thread two crimp tubes onto the end of your strand, but do not crimp them yet.Thread the end of your strand through the loop on the round toggle clasp and back through the two crimp tubes. Crimp the tubes.Remove the bead stopper from the opposite end and add two crimp tubes, but do not crimp them yet.Thread the end of your strand through the loop on the leaf toggle bar and back through the two crimp tubes. Crimp the tubes.Add a crimp cover over each of the four crimp tubes, and gently squeeze them closed. Trim off excess wire.Tip: Check package quantities for each component. You may have extra material to make more than one finished project, or will have leftovers for other projects. In some cases, adding on just one more package of a component may be all you need to make multiple pieces.All designs © Beadaholique Inc.
WHAT YOU'LL NEED: (scroll down for purchase options)
- XCR-67563 - Beadalon Beading Wire Bronze 7 Strand .015 Inch / 30Ft
Project uses 10 inches. You will need 1 package.
- BMB-1836 - Real Copper Small Uniform Round Beads 3 mm (100)
Project uses 20 pieces. You will need 1 package.
- BMB-5303 - Antiqued Copper Plated Fluted Round Beads 5.5mm (72 Beads)
Project uses 10 pieces. You will need 1 package.
- FCL-7511 - Nunn Design Copper Plated Pewter Round Toggle Clasp Ring 18.5mm (1)
Project uses 1 piece. You will need 1 package.
- FCL-7503 -
Project uses 1 piece. You will need 1 package.
- FCR-1254 - Bright Copper Crimp Beads 2mm x 1.2mm (100)
Project uses 4 pieces. You will need 1 package.
- FCR-1008 - Bright Copper Crimp Bead Covers 3mm (x50)
Project uses 4 pieces. You will need 1 package.
For closed captions/subtitles, click the CC icon on the video player after starting the video.
Earn Reward Points with your purchase of project components or tools.