Note: Components and tools listed within this INSTRUCTIONS box and the printer-friendly PDF, if available, may have been discontinued since
this project was published. Refer to the PURCHASE COMPONENTS and TOOLS AND OTHER SUPPLIES sections for current availability.
These instructions will make a 7 1/2 inch bracelet. For a longer or shorter bracelet, cut a bigger or smaller piece of cotton cord.
- Cut one 6 1/2 inch piece of the woven cotton cord.
- Slide the ornate square large hole bead to the center of the cord. Slide two pink O-Rings on either side of the bead.
- On one side, slide one yellow and one orange O-Ring onto the cord about an inch from the center. Then add the sun pattern large hole bead. Slide one pink and one orange O-Ring onto the cord after it.
- On the other side, slide on one orange and one yellow O-Ring, then add the swirl pattern large hole bead. Slide on one pink and one orange O-Ring after it.
- Place a dab of E6000 on the tip of one side of your cord and fit it into one of the silver cord ends. Repeat for the other side of your bracelet. Let the E6000 dry for a few hours.
- Using your pliers, open a jump ring. Slide it through the loop of one of your cord ends and then add one piece of the magnetic clasp. Close the jump ring. Open another jump ring and repeat this step for the other end of your cord, attaching the other half of the magnetic clasp.
- Your bracelet is ready to wear!
WHAT YOU'LL NEED: (scroll down for purchase options)
- XCR-4006 - Multi-Colored Cotton Cord, Round Woven Strands 6mm Thick, 3 Feet, Brown / Blue Mix
Project uses 6.5 inches. You will need 1 package.
- FCL-6818 - Beadsmith Silver Plated Flat Round Magnetic Clasps 8mm Diameter (2 Sets)
Project uses 1 set. You will need 1 package.
- FCR-1607 - Beadsmith Silver Plated Barrel Cord Ends With Ring 12mm Long - Fits Up To 6.5mm Cords (4)
Project uses 2 pieces. You will need 1 package.
- FRC-031 - Rubber O-Ring Jump Ring Spacers 10mm Diameter - Tangerine (10)
Project uses 4 pieces. You will need 1 package.
- FRC-049 - Rubber O-Ring Jump Ring Spacers 10mm Diameter - Flamingo (10)
Project uses 4 pieces. You will need 1 package.
- FRC-032 - Rubber O-Ring Jump Ring Spacers 10mm Diameter - Lemon (10)
Project uses 2 pieces. You will need 1 package.
- BMB-8332 - Silver Tone European Style Large Hole Bead With Spiral Swirl Pattern (1)
Project uses 1 piece. You will need 1 package.
- BMB-8158 - Silver Tone European Style Large Hole Bead With Sun Pattern (1)
Project uses 1 piece. You will need 1 package.
- BMB-8163 - Silver Tone European Style Large Hole Ornate Square Bead With Rope Edge (1)
Project uses 1 piece. You will need 1 package.
- FJR-5200 - Silver Plated Open Jump Rings 4mm 19 Gauge (50)
Project uses 2 pieces. You will need 1 package.
- XTL-1054 - E6000 Industrial Strength Glue Adhesive (0.18 fl oz)
Project uses 1 tube. You will need 1 package.
RECOMMENDED TOOLS:- XTL-5511 - Beadsmith Jeweller's Micro Pliers Chain Nose Flat Nose
- XTL-5514 - Beadsmith Jewelry Fine Round Nose Micro Pliers
- XTL-5700 - Fiskars 5 Precision Tip Scissors - Super Sharp