Kavala Cuff in Night

Note: Components and tools listed within this INSTRUCTIONS box and the printer-friendly PDF, if available, may have been discontinued since this project was published. Refer to the PURCHASE COMPONENTS and TOOLS AND OTHER SUPPLIES sections for current availability.

1. Begin by cutting 6 rings of memory wire. Cut each ring so it is a slightly over lapping circle.
2. Use your round nose pliers to bend one end of each wire into a small wire loop facing the outer side of the bracelet. Take one eye pin and thread it through one loop, add two iris seed beads, thread it though the next loop and add two iris seed beads. Continue up through all six loops. When you are through all six, make a simple wire loop to secure the eye pin in place.
3. You are going to be using your bead stopper to space your wires as you work. Start by placing it near where all your looped ends are joined with the eye pin. Just place each wire into the grooves of the bead stopper at even intervals.
4. See the wires as 1-6, starting at the top of the bracelet. You will thread the beads in this order. See the photos for reference.
5. Wire 1 and 2 - one gold two hole brick. Wire 3 and 4 - one black two hole brick. Wire 5 and 6 - one gold two hole brick.
6. Wire1 - six iris seed beads. Wire 2 - two iris seed beads. Wire 3 - two iris seed beads. Wire 4 - two iris seed beads. Wire 5 - two iris seed beads. Wire 6 - six iris seed beads.
7. Wire 2 and 3 - one gold two hole brick. Wire 4 and 5 - one black two hole brick. Wire 2 - two iris seed beads. Wire 3 - two iris seed beads. Wire 4 - two iris seed beads. Wire 5 - two iris seed beads.
8. Wire 1 and 2 - one black two hole brick. Wire 3 and 4 - one gold two hole brick. Wire 5 and 6 - one black two hole brick.
9. Wire1 - six iris seed beads. Wire 2 - two iris seed beads. Wire 3 - two iris seed beads. Wire 4 - two iris seed beads. Wire 5 - two iris seed beads. Wire 6 - six iris seed beads.
10. Wire 2 and 3 - one black two hole brick. Wire 4 and 5 - one gold two hole brick. Wire 2 - two iris seed beads. Wire 3 - two iris seed beads. Wire 4 - two iris seed beads. Wire 5 - two iris seed beads.
11. Continue this pattern all the way around the memory wire. Move your bead stopper as needed to scoot your beads into their proper place. When you come to the end, remove your bead stopper to continue working.
12. Use your round nose pliers to bend the end of each wire into a small loop facing the outer side of the bracelet. Repeat the process with the eye pin the same way as the other side. If needed, snip the ends of the wire to achieve the desired leng

• BCP-10609 - CzechMates Glass 2-Hole Rectangle Brick Beads 6x3mm - Jet Black (1 Strand)
  Project uses 1 strand. You will need 1 package.


• BCP-10620 - CzechMates Glass 2-Hole Rectangle Brick Beads 6x3mm - Matte Metallic Flax /1 Str
  Project uses 1 strand. You will need 1 package.


• JSK-0312 - Toho Round Seed Beads 11/0 504 'Higher Metallic Iris Violet' 8g
  Project uses 1 tube. You will need 1 package.


• WXM-020 - Bright Silver Color Bracelet Memory Wire 12 Loops
  Project uses 1 piece. You will need 1 package.


• FHP-6261 - Silver Plated Open Eye Pins 21 Gauge 2 Inch (x50)
  Project uses 2 pieces. You will need 1 package.

• XTL-5514 - Beadsmith Jewelry Fine Round Nose Micro Pliers
• XTL-5511 - Beadsmith Jeweller's Micro Pliers Chain Nose Flat Nose
• XTL-5612 - Beadalon Memory Wire Shears Cutting Pliers -Strong & Easy
• XTL-3000 - Bead Stopper- Stop Beads Sliding Off Stringing Material