Retired - Industrial Denim Bracelet

Name: Retired - Industrial Denim Bracelet
Brand: Beadaholique
SKU: B2142
Availability: OutOfStock

PROJECT B2142

Designer: Kat Silvia

Skill Level: Intermediate

Save to Wishlist

Printer Friendly PDF
(if available)

Denim has been a fashion staple for decades now, and this classic textile has inspired this riveted bracelet so you can show off a retro cool look.

Instructions

Note: Components and tools listed within this INSTRUCTIONS box and the printer-friendly PDF, if available, may have been discontinued since this project was published. Refer to the PURCHASE COMPONENTS and TOOLS AND OTHER SUPPLIES sections for current availability.

These instructions will give you a bracelet that is 6 inches. To make a longer or short bracelet you will need to adjust the length of the denim cord.

Take the bracelet bending pliers and carefully bend the embellished bar into a curve. Set this aside.
Cut off 6.5 inches of the flat denim cord.
Find the mid-point of the cord. Center the embellished bar on the flat cord. Mark each hole on the denim with a pen or pencil.
Take your hole punch pliers and punch 2 holes where you just marked.
Take two compression rivets and attach the bar to the cord. Because the cord is curved you may need to use the edge of your work block.
From the edge of one of the rivet, measure 3/4". Make another mark. Punch a hole and add another rivet.
From the edge of the last rivet, measure 3/4". Make another mark. Punch a hole and add another rivet.
Repeat that process on the other side.
Separate the magnetic clasp.
Add a few drops of Super New Glue into the well of one side of the clasp. Carefully place one cord end into this side of the clasp.
Repeat on the other side. Make sure to leave the ends separated while the glue dries.

WHAT YOU'LL NEED: (scroll down for purchase options)

PND-05068 - TierraCast Lead-Free Pewter Embellishment Bar, Textured 12x40mm 1 Piece, Brass Oxide Finish
Project uses 1 piece. You will need 1 package.

FCL-1617 - Antiqued Brass Plated Riveted Magnetic Clasp For Regaliz 10mm Flat Cork Cord - 1 Set
Project uses 1 piece. You will need 1 package.

FCO-4784 - TierraCast Brass Oxide Finish Double Round Cap Compression Rivet Set 4mm - Pack Of 10
Project uses 6 pieces. You will need 1 package.

CHA-0355 - Faded Denim Cord, Flat 10x2mm Strand, Sold By The Foot, Denim Blue
Project uses 6.5 Inches. You will need 1 package.

XTL-1059 - Eurotool Super New Glue - Heavy Duty Adhesive - 3 Gram Bottle
Project uses 1 piece. You will need 1 package.

RECOMMENDED TOOLS:

XTL-5503 - BeadSmith Little Cut Flush Cutter For Rubber And Leather Cord
XTL-0786 - TierraCast 4mm Rivet Setter Tool - 1 Tool
XTL-0258 - Mini Rubber And Steel Bench Block For Metal Working And Wire Hardening
XTL-2152 - Beadsmith Jeweler's Chasing Hammer - 1 Inch Head - Metal Smithing
XTL-0061 - Eurotool EuroPunch 1.8mm Round Hole Punch Pliers For Bottle Caps
XTL-0084 - BeadSmith Bracelet Bending Pliers - Gently Curve Bracelets And Components

Additional Information

Theme	Men's
Ingredients	FCO-4784, XTL-1059,

Purchase Components

Purchase the components needed to make this project. Change quantities as needed to make multiple pieces. This project is RETIRED. Please review project instructions carefully—some items may no longer be available for this project and will not be listed below. Tip: Save this project to your wishlist to easily return to project instructions.

            
You will need 1 package(s).
1 package = .

             / Package | SKU: FCO-4784

Eurotool Super New Glue - Heavy Duty Adhesive - 3 Gram Bottle

            Eurotool Super New Glue - Heavy Duty Adhesive - 3 Gram Bottle
        
You will need 1 package(s).
1 package = 1 Bottle.

                $2.59
            
             / Package | SKU: XTL-1059