Note: Components and tools listed within this INSTRUCTIONS box and the printer-friendly PDF, if available, may have been discontinued since
this project was published. Refer to the PURCHASE COMPONENTS and TOOLS AND OTHER SUPPLIES sections for current availability.
- Begin with four separate head pins, and thread the following on each: a 6/0 yellow Czech seed bead, an orange lucite flower, a blue lucite flower, a hot pink lucite flower, a bright green lucite leaf, and a small silver daisy spacer. Create a wrapped wire loop on each head pin and trim off excess wire. Set these lucite flower dangles aside.
- Using your flush cutters, cut a piece of beading wire at one foot long. Secure one end of your wire with a Bead Stopper.
- Onto your beading wire, thread five turquoise Czech fire polish beads and a lucite flower dangle. Repeat this stringing sequence three more times, followed by five more turquoise Czech fire polish beads.
- Onto the very end of your strand, thread a crimp tube- but do not crimp it yet. Thread your wire through the loop on one half of your toggle clasp and back through the crimp tube and several consecutive beads. Pull the wire snug, leaving a little wiggle room for the clasp, and crimp your tube.
- Remove the Bead Stopper from the opposite end of your bracelet and repeat the previous step. Trim excess wire from both ends of the bracelet.
- Place a crimp bead cover over each of the crimps and gently squeeze shut.
WHAT YOU'LL NEED: (scroll down for purchase options)
- BCP-40043 - Lucite 6 Petal Tropical Flower Beads Matte Hot Neon Pink 30mm (4)
Project uses 4 pieces. You will need 1 package.
- FHP-05326 - Silver Plated Head Pins - 21 Gauge 3 Inches (25)
Project uses 4 pieces. You will need 1 package.
- FCR-1070 - Silver Plated Stardust Sparkle Crimp Bead Covers 4mm (144)
Project uses 2 pieces. You will need 1 package.
- FCR-1216 - Beadalon Silver Plated Crimp Tubes 1.5mm (68 Beads)
Project uses 2 pieces. You will need 1 package.
- XCR-5493 - Soft Flex, Soft Touch 49 Strand Medium Beading Wire .019 Inch Thick, 30 Feet, Satin Silver
Project uses 1 foot. You will need 1 package.
- FCL-3050 - Silver Plated Flower Toggle Clasps 14mm (5 Sets)
Project uses 1 piece. You will need 1 package.
- BCS-6540 - Czech Seed Beads 6/0 Sunshine Yellow Opaque (1 Ounce)
Project uses 4 pieces. You will need 1 package.
- BCP-40053 - Lucite Tulip / Lily Of The Valley Flower Bead Caps Matte Orange 6x10mm (12)
Project uses 4 pieces. You will need 1 package.
- BCP-40001 - Lucite Plumeria Flower Beads Matte Deep Aqua Blue 26mm (6)
Project uses 4 pieces. You will need 1 package.
- BMB-3242 - TierraCast Silver Plated Antiqued Pewter Daisy Spacer Beads 5mm (50)
Project uses 4 pieces. You will need 1 package.
- BCP-3667 - Czech Fire Polished Glass Beads 6mm Round Blue Turquoise (25)
Project uses 25 pieces. You will need 1 package.
RECOMMENDED TOOLS:- XTL-5600 - Xuron Sharp Flush Cutter Pliers - Wire/Soft Flex
- XTL-5514 - Beadsmith Jewelry Fine Round Nose Micro Pliers
- XTL-5230 - Double Notch Crimping Pliers - Works on 2mm And 3mm Crimps