Note: Components and tools listed within this INSTRUCTIONS box and the printer-friendly PDF, if available, may have been discontinued since
this project was published. Refer to the PURCHASE COMPONENTS and TOOLS AND OTHER SUPPLIES sections for current availability.
By following the instructions below you will make one earring. Repeat all instructions to make the second earring.
- Begin by setting the stone into the setting. You can do this by using a popsicle stick or the side of a nylon jaw pliers. Please watch our video here to see this easy technique. Once your stone is in the setting, set it aside.
- Using your flush cutters, cut off 8 inches of beading wire.
- On to this beading wire string one 8mm crystal and slide this down to the center of the wire.
- Then, on one side of the wire string on one gold bead, one 6mm crystal, one gold bead, one 6mm crystal, one gold bead, and one 4mm crystal. The repeat this on the other side of the wire.
- Next string each end of the wire through the two holes of the set stone.
- Then on one side string one 4mm crystal, one gold bead, and one 4mm crystal. Repeat on the other strand.
- Take both wires up through one gold bead and one 6mm crystal.
- Onto both wires string on one crimp bead and one closed jump ring. Thread the wire back down through the crimp tube. Pull snug and adjust the wires to get them nice and even. Then using the crimpers, crimp the crimp tube. Use you flush cutters to trim any excess wire. Add a crimp cover.
- Finally, open the loop of the earring hook, same as you would a jump ring and attach it to the jump ring. Close the loop and you're all done!
WHAT YOU'LL NEED: (scroll down for purchase options)
- FEA-9452 - Large French Ear Wire, 16mm Long 20 Gauge Wire, 20 Pieces, Gold Plated
Project uses 2 pieces. You will need 1 package.
- SWC-9365 - Austrian Crystal, 1122 Rivoli Fancy Stones 14mm, 2 Pieces, Emerald Sf
Project uses 2 pieces. You will need 1 package.
- SWCR-4404 - Austrian Crystal Fancy Stone Setting, Fits 1122 14mm Rivoli, 2 Pieces, Gold Plated
Project uses 2 pieces. You will need 1 package.
- SWC-0885 - Austrian Crystal, 5000 Round Beads 8mm, 8 Pieces, Light Siam
Project uses 2 pieces. You will need 1 package.
- SWC-0685 - Austrian Crystal, 5000 Round Beads 6mm, 10 Pieces, Light Siam
Project uses 10 pieces. You will need 1 package.
- SWC-0485 - Austrian Crystal, 5000 Round Beads 4mm, 12 Pieces, Light Siam
Project uses 12 pieces. You will need 1 package.
- FJR-4012 - 22K Gold Plated Closed Jump Rings 5mm 19 Gauge (20)
Project uses 2 pieces. You will need 1 package.
- FCR-1058 - Bright Gold Tone Crimp Bead Covers 5mm (x144)
Project uses 2 pieces. You will need 1 package.
- FCR-1719 - BeadSmith Crimp Tubes, 2.5x2.5mm, 100 Pieces, Gold Plated
Project uses 2 pieces. You will need 1 package.
- XCR-67543 - Beadalon Wire Satin Gold 7 Strand .015 Inch / 30Ft
Project uses 16 Inches. You will need 1 package.
RECOMMENDED TOOLS:- XTL-5608 - Xuron 4 In 1 Crimping Pliers - Works On 1, 2 And 3mm Crimps!
- XTL-5600 - Xuron Sharp Flush Cutter Pliers - Wire/Soft Flex
- XTL-5511 - Beadsmith Jeweller's Micro Pliers Chain Nose Flat Nose
- XTL-0074 - Eurotool Nylon Jaw Pliers Chain Nose- For Scratch-Free Wire Work