Retired - Embrace Love Necklace

PROJECT N850
Designer: Julie Bean
Skill Level: Intermediate
A timeless message of embrace love is metal stamped on an ornate stamping blank in this simple but elegant design. With just two words, this is a great beginner metal stamping project.
Instructions

Note: Components and tools listed within this INSTRUCTIONS box and the printer-friendly PDF, if available, may have been discontinued since this project was published. Refer to the PURCHASE COMPONENTS and TOOLS AND OTHER SUPPLIES sections for current availability.

  1. Begin this project by watching the video: How to Metal Stamp a Cuff Bracelet using ImpressArt Tools. Although the video does not show this exact project, it is going to show you how to use the sticker guide, how to line your letters up along the sticker, how to metal stamp, and how to fill in the impressions with the stamp enamel marker.
  2. Set your stamping blank down on your bench block. Next, place a stamp guide sticker onto the blank. You want it positioned going horizontal long ways across the blank and also just slightly below center (this way when you stamp, your letters will be centered). Let the stamp sticker go over both sides of the blank so it actually ends up taping the blank to the block. This will help stabilize it when you stamp.
  3. The combination of the words embrace love, including the space between them, is 12 characters long. Following what you learned in the video about how to do your letter spacing using the bracelet stamp guide sticker, write the words embrace love on your sticker using a pen. You want your words to be centered on the tape and on the blank.
  4. After you have done all the prep work from above, stamp your letters using your alphabet set and hammer.
  5. Once all the letters have been stamped, go over them with the stamp enamel marker. Wait a minute or so and then wipe away any excess ink.
  6. Take your hole punch pliers and punch a hole in each top corner of your stamped blank. To see how to do this, please watch the video: How to Use Eurotool Europunch Metal Hole Punch Pliers. Just make sure that you don't punch it too close to the edge and accidentally punch the side of the stamping.
  7. Next, take your premade chain necklace, find the middle point, and cut at that middle point using your flush cutters.
  8. Open a jump ring and link it to one of the holes in your pendant as well as one side of your now cut chain necklace. Close the jump ring.
  9. Repeat the previous step on the other side of your necklace.
  10. All done!
WHAT YOU'LL NEED: (scroll down for purchase options)
  • AXC-98944 - 22K Gold Plated Fine Rolo Chain Necklace with Lobster Clasp - 2mm Diameter Links 18 Inches Long
    Project uses 1 piece. You will need 1 package.

  • FJR-5250 - 22K Gold Plated Open Jump Rings 5mm 20 Gauge (100)
    Project uses 2 pieces. You will need 1 package.

  • PND-6238 - Brass Stamping, Large Rectangular Ornate Blank 38x20x0.5mm, 2 Pieces, Brass
    Project uses 1 piece. You will need 1 package.

  • XTL-7200 - ImpressArt Antique Stamp Enamel Marker, Darken Stamped Impressions, 1.1 OZ, Black
    Project uses 1 piece. You will need 1 package.

  • XTL-8259 - ImpressArt Bracelet Guides Booklet, for Spacing Stamped Designs in a Line, 36 Stickers
    Project uses 1 piece. You will need 1 package.

RECOMMENDED TOOLS:
  • XTL-0061 - Eurotool EuroPunch 1.8mm Round Hole Punch Pliers For Bottle Caps
  • XTL-5450 - Xuron Jeweler's Super Fine Pliers Chain Nose Flat Nose
  • XTL-0727 - ImpressArt 33-Piece Lowercase Alphabet Stamps Jeanie 4mm - 1 Set
  • XTL-6236 - ImpressArt Steel Stamping Block, Small Size with Rubber Feet 2x2, 1 Piece, Steel
  • XTL-0277 - ImpressArt Brass Hammer For Metal Stamping - 1 Pound - 1 Piece
  • XTL-5600 - Sharp Flush Cutter Pliers - For Cutting Beading Wire, 1 Piece
Additional Information
Theme Personalization
Ingredients AXC-98944, FJR-5250, XTL-7200, XTL-8259,
Useful Techniques & Learning Guides

Purchase Components

Purchase the components needed to make this project. Change quantities as needed to make multiple pieces. This project is RETIRED. Please review project instructions carefully—some items may no longer be available for this project and will not be listed below. Tip: Save this project to your wishlist to easily return to project instructions.
Finished Rolo Chain Necklace, Round Links with Lobster Clasp 2mm, 18 Inches, 22K Gold Plated
You will need 1 package(s).
1 package = 1 Piece.
$7.29 / Package | SKU: AXC-98944
22K Gold Plated Open Jump Rings 5mm 20 Gauge (100 pcs)
You will need 1 package(s).
1 package = 100 Pieces.
$4.94 / Package | SKU: FJR-5250
ImpressArt Antique Stamp Enamel Marker, Darken Stamped Impressions, 1.1 OZ, Black
You will need 1 package(s).
1 package = 1 Piece.
$12.99 / Package | SKU: XTL-7200
ImpressArt Bracelet Guides Booklet, for Spacing Stamped Designs in a Line, 36 Stickers
You will need 1 package(s).
1 package = 1 Booklet.
$9.89 / Package | SKU: XTL-8259
Earn Reward Points Earn Reward Points with your purchase of project components or tools.

Tools and Other Supplies:

Eurotool EuroPunch 1.8mm Round Hole Punch Pliers
$18.49 / Package | SKU: XTL-0061
Xuron Jeweler's Super Fine Pliers Chain Nose Flat Nose
$25.99 / Package | SKU: XTL-5450
ImpressArt Brass Hammer For Metal Stamping - 1 Pound - 1 Piece

Related Video [VIEW ALL VIDEOS]

Accessible Options For closed captions/subtitles, click the CC icon on the video player after starting the video.

You recently viewed

Clear recently viewed