Note: Components and tools listed within this INSTRUCTIONS box and the printer-friendly PDF, if available, may have been discontinued since
this project was published. Refer to the PURCHASE COMPONENTS and TOOLS AND OTHER SUPPLIES sections for current availability.
If you purchase one more bezel pendant, you will have enough supplies to make two necklaces, so you can make one for a friend!
- Apply a thin layer of E6000 glue to the back side of a 25x18mm lucite oval cameo and press it into place in an antique brass oval bezel pendant. Allow the glue to set before continuing.
- Cut a piece of 24pp crystal AB gold plated rhinestone cup chain that is 18 links (about 3.25") long.
- Apply a bit of E6000 along the back side of the chain and then press it into place around the outside edge of your bezel pendant. Make sure that the end links are up against the hanging loop, and that the sides of the chain are flush with the back of the pendant so that it lays flat. Allow the glue to dry thoroughly before continuing.
- Attach a 22k gold plated 5mm, 20 gauge jump ring to the hanging loop on your pendant.
- Use the tapered end of a piece of dark raspberry silk fairy ribbon to thread it through the jump ring on your pendant. Cut the last 2" off of one end of the ribbon to remove the tapered end. Measure 18" from your cut end and cut.
- Place a dab of E6000 into one 5x5mm 22k gold plated ribbon crimp. Keeping the ribbon folded up on the end, as it naturally is, so that it will fit into the crimp, slide one end into the ribbon crimp and pinch it closed using a pair of chain nose pliers. Wipe away any excess glue, and press the sides of the ribbon into the sides of the crimp to tidy the ends up. (The glue will hold them in.)
- Repeat this process to attach a crimp to the other end of the ribbon. Then allow the glue to dry on both ends before continuing.
- Use a jump ring to attach a 22k gold plated sleek lobster clasp to one of the ribbon crimps. Then attach another jump ring to the ribbon crimp on the other side.
WHAT YOU'LL NEED: (scroll down for purchase options)
- SPCB-2505 - Lucite Oval Cameo - Black With Ivory Lady And Flowers 25x18mm (2 Pieces)
Project uses 1 piece. You will need 1 package.
- PND-6982 - Antiqued Brass Large Oval Bezel Pendant - 25x18mm (1)
Project uses 1 piece. You will need 1 package.
- CHA-2022 - Austrian crystal Gold Plated Rhinestone Cup Chain 24PP Crystal AB - BY THE FT
Project uses 3.25 inches. You will need 1 package.
- XCR-47017 -
Project uses 20 inches. You will need 1 package.
- FCR-7050 - 22K Gold Plated Ribbon Pinch Crimp Cord Ends 5 x 5mm (10 Pieces)
Project uses 2 pieces. You will need 1 package.
- FJR-5250 - 22K Gold Plated Open Jump Rings 5mm 20 Gauge (100)
Project uses 3 pieces. You will need 1 package.
- FCL-2531 - 22K Gold Plated Sleek Lobster Claw Clasps 12mm (10)
Project uses 1 piece. You will need 1 package.
- XTL-1054 - E6000 Industrial Strength Glue Adhesive (0.18 fl oz)
Project uses 1 tube. You will need 1 package.
RECOMMENDED TOOLS:- XTL-5600 - Xuron Sharp Flush Cutter Pliers - Wire/Soft Flex
- XTL-5511 - Beadsmith Jeweller's Micro Pliers Chain Nose Flat Nose
- XTL-5700 - Fiskars 5 Precision Tip Scissors - Super Sharp