Retired - Bridal Bliss Bracelet

Name: Retired - Bridal Bliss Bracelet
Brand: Beadaholique
SKU: B691
Availability: OutOfStock

PROJECT B691

Designer: Julie Bean

Skill Level: Beginner

Save to Wishlist

Printer Friendly PDF
(if available)

This lovely bracelet would make a treasured keepsake for a bride to wear on her special day. It features three strands of wire wrapped seed pearl chain with delicate dangles.

Instructions

Note: Components and tools listed within this INSTRUCTIONS box and the printer-friendly PDF, if available, may have been discontinued since this project was published. Refer to the PURCHASE COMPONENTS and TOOLS AND OTHER SUPPLIES sections for current availability.

This project makes for a 7.25 inch bracelet. If you want a longer or shorter one, adjust your supplies and the instructions accordingly. The actual chain accounts for 6 inches of the bracelet and the strand reducers/clasp add another 1.25 inches. You will also need a ruler for this project.

Begin by cutting your gemstone chain into 3 pieces, 6 inches long each. You will need to measure each length out, there will be a little bit of chain left over.
Open a jump ring and attach it to the loop on one end of one cut piece of chain. Also link this same jump ring onto the side hole of one of your strand reducers. Close the jump ring. Repeat this step on the other side of your chain with another jump ring, attaching this one to the side hole on your second strand reducer. Please take note that there is a textured and smooth side to your strand reducers, you will want to make sure you connect them to the chain with either both the textured sides or both the smooth sides facing up.
Repeat the step above with your second chain, attaching it to the middle holes in your strand reducers. Repeat with your third piece of chain, attaching it to the last remaining side holes of your strand reducers.
Open a jump ring and connect it to the loop on one side of your box clasp as well as the outside loop on one of your strand reducers. Close the jump ring.
Repeat the step above with another jump ring, attaching the other other side of your bracelet to the other side of the clasp.
All done! Enjoy your pretty new bracelet.

WHAT YOU'LL NEED: (scroll down for purchase options)

FJR-5452 - 22K Gold Plated Open Jump Rings 4mm 22 Gauge (50)
Project uses 8 pieces. You will need 1 package.

FCL-4844 - 23K Gold Plated Box Clasp - Disk Shaped With Austrian crystal 12mm Diameter (1)
Project uses 1 piece. You will need 1 package.

CHX-1021 - Tiny Hanging White Seed Pearl Gold Vermeil Wire Wrapped Chain 3.5mm
Project uses 20 inches. You will need 20 packages.

FCO-9227 - TierraCast 22K Gold Plated Lead-Free Pewter 3-Hole Strand Reducer 7.5x10mm (2)
Project uses 2 pieces. You will need 1 package.

RECOMMENDED TOOLS:

XTL-5600 - Xuron Sharp Flush Cutter Pliers - Wire/Soft Flex
XTL-5511 - Beadsmith Jeweller's Micro Pliers Chain Nose Flat Nose

Additional Information

Theme	Special Occasion, Bridal
Ingredients	FJR-5452, CHX-1021, FCO-9227,

Purchase Components

Purchase the components needed to make this project. Change quantities as needed to make multiple pieces. This project is RETIRED. Please review project instructions carefully—some items may no longer be available for this project and will not be listed below. Tip: Save this project to your wishlist to easily return to project instructions.

22K Gold Plated Open Jump Rings 4mm 22 Gauge (50 pcs)

            22K Gold Plated Open Jump Rings 4mm 22 Gauge (50 pcs)
        
You will need 1 package(s).
1 package = 50 Pieces.

                $3.07
            
             / Package | SKU: FJR-5452

            
You will need 20 package(s).
1 package = .

             / Package | SKU: CHX-1021

TierraCast 22K Gold Plated Lead-Free Pewter 3-Hole Strand Reducer 7.5x10mm (2 pcs)

            TierraCast 22K Gold Plated Lead-Free Pewter 3-Hole Strand Reducer 7.5x10mm (2 pcs)
        
You will need 1 package(s).
1 package = 2 Pieces.

                $2.69
            
             / Package | SKU: FCO-9227