Retired - Marine Point Earrings

PROJECT E7033
Designer: Rachel Zaimont
Skill Level: Intermediate
Color blocking with tape is an easy technique that allows you to paint the clean, crisp line of aquamarine Vintaj patina in these lively, modern earrings.
Instructions

Note: Components and tools listed within this INSTRUCTIONS box and the printer-friendly PDF, if available, may have been discontinued since this project was published. Refer to the PURCHASE COMPONENTS and TOOLS AND OTHER SUPPLIES sections for current availability.

In addition to the materials listed above, you will also need some Scotch tape or other tape that will not leave a sticky residue, and a few paper towels. By following the instructions below you will make one earring. Repeat all instructions to make the second earring.
  1. Take one Vintaj Vogue triangle stamping blank and place one corner without a hole into the 1.5mm slot of the BeadSmith two-hole metal punch tool. Position the blank so the pin will make a hole symmetrical to the existing hole in the other corner. Then twist the handle to punch the hole.
  2. Place the triangle stamping blank onto your work surface with the two holes at the top and the point pointing down. Take a piece of Scotch tape and place it onto the surface of the blank so it covers the top 1/3 of the piece, including the two holes. Stick it firmly to the piece so no paint can get under it.
  3. Pour out a little bit of marine blue Vintaj patina onto your work surface. Using a dry paintbrush, paint the patina onto the exposed point of the triangle stamping blank. Make sure to paint up to and over the bottom edge of the tape, to ensure a crisp line. Wait several minutes for the patina to dry.
  4. When the patina is completely dry, peel the tape off the front of the blank and discard it.
  5. Since this stamping blank is raw brass, you will need to seal it with metal sealer to preserve its bright color. Pour out a little bit of Vintaj glaze onto your work surface. With a clean and dry paintbrush, gently coat the surface with the glaze. Let the glaze dry for a few minutes.
  6. When the glaze on the front is dry, flip the piece over and seal the back to prevent tarnishing. Allow it to dry.
  7. Using flush cutters, cut two 1 inch pieces of gold chain.
  8. Open a jump ring. Slide it through one of the holes at the top of the triangle blank, and also slide on the first link of one piece of chain. Close the jump ring.
  9. Open another jump ring. Slide it through the other hole at the top of the triangle, and also slide on the first link of the other piece of chain. Close the jump ring.
  10. Open another jump ring. Slide on the last link of both pieces of chain, joining them at the top. Close the jump ring.
  11. Open the loop of an earring hook the same way you would open a jump ring. Slide on the jump ring from the previous step. Close the loop.
  12. Enjoy your earrings!
WHAT YOU'LL NEED: (scroll down for purchase options)
  • PND-0233 - Vintaj Vogue Stamping Blanks, Triangle 14mm, 4 Pieces, Brass
    Project uses 2 pieces. You will need 1 package.

  • XTL-9066 - Vintaj Patina Opaque Permanent Ink - Marine Blue - 0.5 Ounce Bottle
    Project uses 1 piece. You will need 1 package.

  • XTL-9090 - Vintaj Mini Glaze - Metal Sealer And Patina Extender - 0.5 Ounce Bottle
    Project uses 1 piece. You will need 1 package.

  • CHA-99970 - Bright 22K Gold Plated Long And Short Chain 2.5x4.5mm - Bulk By The Foot
    Project uses 4 inches. You will need 1 package.

  • FJR-5240 - 22K Gold Plated Open Jump Rings 4mm 21 Gauge (x100)
    Project uses 6 pieces. You will need 1 package.

  • FEA-3030 - 22K Gold Plated Long Elegant Earring Hooks 25mm (50)
    Project uses 2 pieces. You will need 1 package.

RECOMMENDED TOOLS:
  • XTL-880 - ICE Resin, Angled Brushes for ICED Enamels & Paper Sealant, 6 Pack
  • XTL-0284 - BeadSmith Two-Hole Metal Punch, Makes 1.5 and 2mm Holes
  • XTL-5511 - Beadsmith Jeweller's Micro Pliers Chain Nose Flat Nose
  • XTL-5514 - Beadsmith Jewelry Fine Round Nose Micro Pliers
  • XTL-5600 - Xuron Sharp Flush Cutter Pliers - Wire/Soft Flex
Additional Information
Ingredients XTL-9090, CHA-99970, FJR-5240, FEA-3030,

Purchase Components

Purchase the components needed to make this project. Change quantities as needed to make multiple pieces. This project is RETIRED. Please review project instructions carefully—some items may no longer be available for this project and will not be listed below. Tip: Save this project to your wishlist to easily return to project instructions.
Vintaj Mini Glaze - Metal Sealer And Patina Extender - 0.5 Ounce Bottle
You will need 1 package(s).
1 package = 1 Bottle.
$5.89 / Package | SKU: XTL-9090
22K Gold Plated Figaro Chain, 2.5mm, by the Foot
You will need 1 package(s).
1 package = By the Foot.
$2.49 / Package | SKU: CHA-99970
22K Gold Plated Open Jump Rings 4mm 21 Gauge (100 pcs)
You will need 1 package(s).
1 package = 100 Pieces.
$3.39 / Package | SKU: FJR-5240
Earring Findings, Long Earring Hooks 25mm, Gold Plated (25 Pairs)
You will need 1 package(s).
1 package = 25 Pairs.
$10.49 / Package | SKU: FEA-3030
Earn Reward Points Earn Reward Points with your purchase of project components or tools.

Tools and Other Supplies:

The Beadsmith Two-Hole Metal Punch, Makes 1.5 and 2mm Holes
The Beadsmith Jeweller's Micro Pliers Chain Nose Flat Nose
The Beadsmith Jewelry Fine Round Nose Micro Pliers
$6.49 / Package | SKU: XTL-5514

Related Video [VIEW ALL VIDEOS]

Accessible Options For closed captions/subtitles, click the CC icon on the video player after starting the video.

You recently viewed

Clear recently viewed