Retired - Emerald Isle Bracelet

Name: Retired - Emerald Isle Bracelet
Brand: Beadaholique
SKU: B2280
Availability: OutOfStock

PROJECT B2280

Designer: Kat Silvia

Skill Level: Beginner

Save to Wishlist

Printer Friendly PDF
(if available)

This delicate bracelet features a trio of Austrian crystal Links in Emerald with two more charms hanging down the wrist for a sparking adornment.

Instructions

Note: Components and tools listed within this INSTRUCTIONS box and the printer-friendly PDF, if available, may have been discontinued since this project was published. Refer to the PURCHASE COMPONENTS and TOOLS AND OTHER SUPPLIES sections for current availability.

This bracelet is adjustable. When sizing, simply measure the largest size needed to slip over the wrist. From there you will add the adjustable slider bead to wear comfortably. To modify the length, simply adjust the length of chain on both sides respectively. You will also need a scrap of thin wire or thread for this bracelet.

Cut two 4.5 inch lengths of chain.
Open one jump ring and attach it to the end of one length of chain. Attach one channel link and close the jump ring.
Move to the other side of this link and attach another link with another jump ring. Repeat once more to have a length of three links.
Then open one more jump ring and attach the last link to the the other length of chain with another jump ring. Close the jump ring.
Using your thin scrap of wire or thread, thread on the two end links of the chain and using this wire as a needle thread both ends of the chain through the adjustable slider bead. Remove the wire.
Finally take one charm and attach it to one end of the chain using a jump ring. Repeat on the other chain with a second charm.

WHAT YOU'LL NEED: (scroll down for purchase options)

SWFA-1106 - Austrian Crystal, Rhodium Plated Channel Connector Link, 7mm, 4 Pieces, Emerald
Project uses 3 pieces. You will need 1 package.

SWFA-1006 - Austrian Crystal, Rhodium Plated Channel Charm, 7mm, 8 Pieces, Emerald
Project uses 2 pieces. You will need 1 package.

BMB-024 - Adjustable Slider Clasp, Tube with Silicone Center 5.5x6.8mm, 4 Pieces, Silver Tone
Project uses 1 piece. You will need 1 package.

CHA-0177 - Silver Plated Bulk Chain, Round Soldered Links 2mm, By The Foot, Bright Silver
Project uses 9 Inches. You will need 1 package.

FJR-5454 - Silver Plated Open Jump Rings 4mm 22 Gauge (50)
Project uses 6 pieces. You will need 1 package.

RECOMMENDED TOOLS:

XTL-5600 - Xuron Sharp Flush Cutter Pliers - Wire/Soft Flex
XTL-5511 - Beadsmith Jeweller's Micro Pliers Chain Nose Flat Nose
XTL-5514 - Beadsmith Jewelry Fine Round Nose Micro Pliers

Additional Information

Theme	St. Patrick's Day, Delicate, Christmas
Ingredients	BMB-024, CHA-0177, FJR-5454,

Useful Techniques & Learning Guides

Purchase Components

Purchase the components needed to make this project. Change quantities as needed to make multiple pieces. This project is RETIRED. Please review project instructions carefully—some items may no longer be available for this project and will not be listed below. Tip: Save this project to your wishlist to easily return to project instructions.

Adjustable Slider Clasp, Tube with Silicone Center 5.5x6.8mm, Silver Tone (4 Pieces)

            Adjustable Slider Clasp, Tube with Silicone Center 5.5x6.8mm, Silver Tone (4 Pieces)
        
You will need 1 package(s).
1 package = 4 Pieces.

                $4.54
            
             / Package | SKU: BMB-024

Silver Plated Cable Chain, Round Links 2mm, by the Foot

            Silver Plated Cable Chain, Round Links 2mm, by the Foot
        
You will need 1 package(s).
1 package = By the Foot.

                $2.79
            
             / Package | SKU: CHA-0177

Sold out

Silver Plated Open Jump Rings 4mm 22 Gauge (50 pcs)

            Silver Plated Open Jump Rings 4mm 22 Gauge (50 pcs)
        
You will need 1 package(s).
1 package = 50 Pieces.

                $2.49
            
             / Package | SKU: FJR-5454