Retired - Crystal Bronze Shade Etruscan Earrings

PROJECT E606
Designer: Julie Bean
Skill Level: Beginner
Austrian crystal bronze shade mini pear pendant drops shimmer below intricate Vintaj brass filigree in these Etruscan inspired earrings. You can almost imagine them being worn by a lady of ancient Rome or on
Instructions

Note: Components and tools listed within this INSTRUCTIONS box and the printer-friendly PDF, if available, may have been discontinued since this project was published. Refer to the PURCHASE COMPONENTS and TOOLS AND OTHER SUPPLIES sections for current availability.

  1. Remember to double these directions so that you make a matched pair of earrings!
  2. Take one of your Vintaj brass filigrees and using your chain nose pliers, gently close the bottom decorative swirls so that they form nice "loops" to use in the next step. Using your chain nose pliers, just squeeze the brass scroll so that it meets the body of the filigree.
  3. Cut a 7 inch length of Vintaj 26 gauge wire and start making a briolette wrap around one of the Austrian crystal crystal bronze shade 8mm mini pendant drops. Make sure the the end that you are going to be wrapping around the drop is 5 inches long. Start wrapping and keep wrapping around the top of the drop, over and over until you get to the bead hole. Then trim off excess wire with flush cutters. For the top part of your briolette wrap, make the loop and thread through it one of the bottom "loops" of your filigree. Finish the top part of your briolette wrap so that you have a loop at the top (which is already connected to the filigree) and the wrapping from it meets the bottom wrapping. You want it to look as much like a continual wrap as possible even though two ends of wire technically make up this wrap. Repeat this entire step with another two of the Austrian crystal drops.
  4. Cut 5 inches of Vintaj 26 gauge wire. Against the top back side of the filigree, line up 1/4 inch of wire and press against the filigree, you want to position it so that the tail of your wire is sticking up towards the top hole of the filigree. Still holding the 1/4 inch of wire in place, wrap the tail of the wire around the "neck" of the filigree, starting close up to the top hole but not covering it. Start an even, tight wrapping so that you are working your way down the neck of the filigree and covering that 1/4 inch you were holding in place. Keep wrapping until the 1/4 inch is completely covered. Cut off excess wire with flush cutters and take your chain nose pliers to press the rough wire end into the wrapping so that there is not a sharp exposed end.
  5. Open the bottom hoop of your brass french ear wire the same way you would open a jump ring. Slide the top loop of your Vintaj filigree into this hoop and close the hoop.
WHAT YOU'LL NEED: (scroll down for purchase options)
  • PND-7343 - Vintaj Natural Brass Latticework Chandelier Drop Charms 30.5mm (2)
    Project uses 2 pieces. You will need 1 package.

  • WCR-4349 - Vintaj Brass Bronze Colored Copper Wire 26 Gauge 120 Feet (1 Spool)
    Project uses 14 inches. You will need 1 package.

  • SWC-99962 - Austrian crystal Pendant, 6128 Mini Pear, 8mm, 8 Pieces, Crystal Bronze Shade
    Project uses 6 pieces. You will need 1 package.

  • FEA-6620 - Vintaj Natural Brass Classic French Ear Wire 20mm (2 Pair)
    Project uses 2 pieces. You will need 1 package.

RECOMMENDED TOOLS:
  • XTL-5600 - Xuron Sharp Flush Cutter Pliers - Wire/Soft Flex
  • XTL-5511 - Beadsmith Jeweller's Micro Pliers Chain Nose Flat Nose
  • XTL-5514 - Beadsmith Jewelry Fine Round Nose Micro Pliers
Additional Information
Ingredients PND-7343, FEA-6620,

Purchase Components

Purchase the components needed to make this project. Change quantities as needed to make multiple pieces. This project is RETIRED. Please review project instructions carefully—some items may no longer be available for this project and will not be listed below. Tip: Save this project to your wishlist to easily return to project instructions.
Vintaj Natural Brass Latticework Chandelier Drop Charms 30.5mm (2 pcs)
You will need 1 package(s).
1 package = 2 Pieces.
$4.17 / Package | SKU: PND-7343
Vintaj Natural Brass Classic French Ear Wire 20mm (2 Pairs)
You will need 1 package(s).
1 package = 2 Pairs.
$2.39 / Package | SKU: FEA-6620
Earn Reward Points Earn Reward Points with your purchase of project components or tools.

Tools and Other Supplies:

The Beadsmith Jeweller's Micro Pliers Chain Nose Flat Nose
The Beadsmith Jewelry Fine Round Nose Micro Pliers
$6.49 / Package | SKU: XTL-5514

Related Video [VIEW ALL VIDEOS]

Accessible Options For closed captions/subtitles, click the CC icon on the video player after starting the video.

You recently viewed

Clear recently viewed