Retired - Cosmic Diva Earrings in Atomic Cherry

PROJECT E1031
Designer: Megan Milliken
Skill Level: Beginner
These futuristic earrings feature Austrian crystal components and would be a fun and funky accent for when you're feeling out of this world!
Instructions

Note: Components and tools listed within this INSTRUCTIONS box and the printer-friendly PDF, if available, may have been discontinued since this project was published. Refer to the PURCHASE COMPONENTS and TOOLS AND OTHER SUPPLIES sections for current availability.

Remember to double these instructions to create your matched pair of earrings.
  1. Apply a small amount of E6000 adhesive to the backside of a crystal CAL 20mm crystal cosmic ring, making sure you keep your glue to the inner part of the back of the ring. If your glue goes too far to the outside, it will show on the sides of your earring. In this design, the foiled side is the back side.
  2. Place your cosmic ring glue side down onto a 19.5mm silver filled stamping blank, making sure it's completely centered. Allow glue to set for an hour before continuing.
  3. Place a good amount of E6000 into the center of the cosmic ring on the stamping blank. There should be a good sized dab, but not too much. It should be less than half way up the center of the ring.
  4. Place a 14mm fuchsia rivoli point side down into the glue in the center of the ring. Make sure it's centered and leave to dry overnight.
  5. Put a 6mm fuchsia bicone bead onto a 1 1/2", 21 gauge silver plated eye pin. Create a simple wire loop after the bead and trim the excess.
  6. Use the loops on the ends of your eye pin to attach one end to your crystals on the blank and the other end to a silver filled long angled earring hook.
WHAT YOU'LL NEED: (scroll down for purchase options)
  • SWC-9022 -
    Project uses 2 pieces. You will need 2 packages.

  • PND-3018 - Silver Filled Stamping Blank, Circle With Loop 19.5mm, 1 Piece, Silver
    Project uses 2 pieces. You will need 2 packages.

  • SWC-9366 - Austrian Crystal, 1122 Rivoli Fancy Stones 14mm, 2 Pieces, Fuchsia Sf
    Project uses 2 pieces. You will need 1 package.

  • SWBB-1684 - Austrian Crystal, 5328 Bicone Beads 6mm, 20 Pieces, Fuchsia
    Project uses 2 pieces. You will need 1 package.

  • FHP-6260 - Silver Plated Open Eye Pins 21 Gauge 1.5 Inch (x50)
    Project uses 2 pieces. You will need 1 package.

  • XTL-1054 - E6000 Industrial Strength Glue Adhesive (0.18 fl oz)
    Project uses 1 tube. You will need 1 package.

RECOMMENDED TOOLS:
  • XTL-5600 - Xuron Sharp Flush Cutter Pliers - Wire/Soft Flex
  • XTL-5032 - Beadsmith Wire Looping Pliers - Concave And Round Nose
  • XTL-5511 - Beadsmith Jeweller's Micro Pliers Chain Nose Flat Nose
Additional Information
Theme Valentine's Day
Ingredients FHP-6260, XTL-1054,

Purchase Components

Purchase the components needed to make this project. Change quantities as needed to make multiple pieces. This project is RETIRED. Please review project instructions carefully—some items may no longer be available for this project and will not be listed below. Tip: Save this project to your wishlist to easily return to project instructions.
Open Eye Pins, 1.5 Inches Long and 21 Gauge Thick Silver Plated (50 Pieces)
You will need 1 package(s).
1 package = 50 Pieces.
$3.85 / Package | SKU: FHP-6260
E6000 Industrial Strength Glue Adhesive (0.18 fl oz)
You will need 1 package(s).
1 package = 1 Piece.
$2.19 / Package | SKU: XTL-1054
Earn Reward Points Earn Reward Points with your purchase of project components or tools.

Tools and Other Supplies:

The Beadsmith Wire Looping Pliers - Concave And Round Nose
The Beadsmith Jeweller's Micro Pliers Chain Nose Flat Nose

Related Video [VIEW ALL VIDEOS]

Accessible Options For closed captions/subtitles, click the CC icon on the video player after starting the video.

You recently viewed

Clear recently viewed