Retired - Victorian Jewel Necklace

PROJECT N531
Designer: Kathy Mannix
Skill Level: Intermediate
Both delicate and bold, this eye-catching necklace harks to the Victorian era. Vintaj brass surrounds Austrian crystal, accentuating each other perfectly.
Instructions

Note: Components and tools listed within this INSTRUCTIONS box and the printer-friendly PDF, if available, may have been discontinued since this project was published. Refer to the PURCHASE COMPONENTS and TOOLS AND OTHER SUPPLIES sections for current availability.

  1. On one side of your Vintaj circle ring pendant, run a line of E6000 adhesive. You can apply it by using a toothpick or piece of wire as an applicator. Turn it so that the glue side is facing down and center on your Vintaj brass garden trellis filigree. Press into place. Take your Austrian crystal crystal 16mm rivoli bead and run a line of glue along the underside edge of the crystal (the back pointed side). Press this into your already glued filigree ring pendant. Let all of these pieces dry fully before going onto the next stage.
  2. Making the bail. Take your Vintaj brass acorn leaves connector and using your chain nose pliers or your fingers, bend it into thirds (3 even sides, 1/3 of the total length each) - so that it forms a triangle. Where the two sides touch, slide it onto the outer edge of your assembled pendant above. You want the edge of the above filigree pendant to be sandwiched between the two sides of the bent acorn leaves bail. Cut 3" of brass wire and bend in half. Thread each end through two open work holes on the front side of your bent bail. Thread the wires all the way through the pendant edge and back out the other side of the bail. Pull snug and then using your fingers, twist the wires together. Make approximately 6 or 7 twists then snip off the remaining wire with your flush cutters. Push the twisted end into the filigree so that the rough ends are tucked inward.
  3. Turn your pendant over so that the front side is facing up. We are now going to cover the wire that is attaching the bail that you made in the step above. Place a dab of E6000 over the wire and press a Vintaj decorative pinwheel washer over the glue dab. A bit of glue will seep through the middle hole. Place an Austrian crystal flatback crystal rhinestone into this glue and press into place. Let dry.
  4. Cut your 2' of chain so that you have one length which is 20" long. Thread one end through the bail. On each end of the chain, open a 4.75mm brass jump ring and connect it to the end link and one half of the clasp. Close the jump ring.
WHAT YOU'LL NEED: (scroll down for purchase options)
  • FCL-4642 - Vintaj Natural Brass Tiny Hook And Eye Clasps 21mm (4 Sets)
    Project uses 1 piece. You will need 1 package.

  • FJR-5347 - Vintaj Natural Brass Jump Rings 4.75mm Open 19 Gauge (25)
    Project uses 1 piece. You will need 1 package.

  • CHA-7190 - Vintaj Natural Brass 3.5mm Round Rolo Chain - Bulk By The Foot
    Project uses 2 feet. You will need 2 packages.

  • PND-7006 - Vintaj Natural Brass Garden Trellis Filigree Stamping 38mm (1)
    Project uses 1 piece. You will need 1 package.

  • PND-7106 - Vintaj Natural Brass Circle Filigree Ring Pendant Link 23mm (1)
    Project uses 1 piece. You will need 1 package.

  • FCO-4610 - Vintaj Natural Brass Filigree Acorn Leaves Connector Beads 12 x 30mm (2)
    Project uses 1 piece. You will need 1 package.

  • PND-7265 - Vintaj Natural Brass Decorative Pinwheel Washer Flowers 7.5mm (10)
    Project uses 1 piece. You will need 1 package.

  • SWF-40900 - Austrian Crystal, Round Flatback Rhinestone SS9 2.5mm, 72 Pieces, Crystal Foiled
    Project uses 1 piece. You will need 1 package.

  • SWC-9400 - Austrian Crystal, 1122 Rivoli Fancy Stones 16mm, 2 Pieces, Crystal SF
    Project uses 1 piece. You will need 1 package.

  • WCR-4201 - Artistic Wire, Copper Craft Wire 24 Gauge Thick, 20 Yard Spool, Antiqued Brass
    Project uses 1 piece. You will need 1 package.

  • XTL-1054 - E6000 Industrial Strength Glue Adhesive (0.18 fl oz)
    Project uses 1 piece. You will need 1 package.

RECOMMENDED TOOLS:
  • XTL-5600 - Xuron Sharp Flush Cutter Pliers - Wire/Soft Flex
  • XTL-5511 - Beadsmith Jeweller's Micro Pliers Chain Nose Flat Nose
Additional Information
Theme Vintage Look
Ingredients FJR-5347, FCO-4610, PND-7265, WCR-4201, XTL-1054,

Purchase Components

Purchase the components needed to make this project. Change quantities as needed to make multiple pieces. This project is RETIRED. Please review project instructions carefully—some items may no longer be available for this project and will not be listed below. Tip: Save this project to your wishlist to easily return to project instructions.
Vintaj Natural Brass Jump Rings 4.75mm Open 19 Gauge (25 Pieces)
You will need 1 package(s).
1 package = 25 Pieces.
$2.79 / Package | SKU: FJR-5347
Vintaj Natural Brass Filigree Acorn Leaves Connector Beads 12 x 30mm (2 pcs)
You will need 1 package(s).
1 package = 2 Pieces.
$3.39 / Package | SKU: FCO-4610
Vintaj Natural Brass Decorative Pinwheel Washer Flowers 7.5mm (10 pcs)
You will need 1 package(s).
1 package = 10 Pieces.
$4.85 / Package | SKU: PND-7265
Artistic Wire, Copper Craft Wire 24 Gauge Thick, Antiqued Brass (20 Yard Spool)
You will need 1 package(s).
1 package = 1 Spool.
$5.79 / Package | SKU: WCR-4201
E6000 Industrial Strength Glue Adhesive (0.18 fl oz)
You will need 1 package(s).
1 package = 1 Piece.
$2.19 / Package | SKU: XTL-1054
Earn Reward Points Earn Reward Points with your purchase of project components or tools.

Tools and Other Supplies:

The Beadsmith Jeweller's Micro Pliers Chain Nose Flat Nose

Related Video [VIEW ALL VIDEOS]

Accessible Options For closed captions/subtitles, click the CC icon on the video player after starting the video.

You recently viewed

Clear recently viewed