Note: Components and tools listed within this INSTRUCTIONS box and the printer-friendly PDF, if available, may have been discontinued since
this project was published. Refer to the PURCHASE COMPONENTS and TOOLS AND OTHER SUPPLIES sections for current availability.
Remember to double these directions to make your matching hair pin set.
- Begin by looking at your hair clip and seeing how the pattern of the filigree creates "rows" of openwork holes. The first row is on the very outer edge and looks like crescent moons. The second row looks like little triangles pointing at each other. The third row looks like little rounds. Keep these rows in mind when reading the directions.
- Cut yourself a 36" length of 28 gauge gold colored wire. Thread the wire through one of the triangle shaped holes in the second row so that a 3" tail sticks out one side. Wrap that 3" tail several times in and around an adjacent hole so that you are securing the wire to your filigree. You want the short tail to be coming out the back of the filigree and the long tail coming out the front. String onto the long tail, 1 Czech charlotte 13/0 seed bead in gold, 1 Czech crystal 3mm bicone in black diamond, and another 13/0 seed bead. Now thread the long end of the tail through the triangle hole next to the one you started from, pull all the way through so just the beads rest on the top side of the filigree. Thread the wire tail up through the triangle hole next to the one you just exited so that the tail is again topside. Pull snug. String onto it the same sequence of beads and thread the tail down through the triangle hole next to it. Repeat this pattern all the way around the filigree until you get to the place where you started. At this point, wrap the long tail in and out of a neighboring filigree hole until the wire is secure. Using flush cutters, cut both tails off.
- Cut yourself a 20" length of 28 gauge gold colored wire. Thread the wire through one of the round shaped holes in the third row so that a 3" tail sticks out one side. Wrap that 3" tail several times in and around an adjacent hole so that you are securing the wire to your filigree. You want the short tail to be coming out the back of the filigree and the long tail coming out the front. String onto the long tail, 1 Czech crystal 4mm bicone in crystal aurum, 1 Czech charlotte 13/0 seed bead in gold, 1 Czech crystal 3mm bicone in black diamond, another 13/0 seed bead, and another 4mm bicone in crystal aurum. Count 4 holes (so you are starting at hole 1) and on the 4th hole, thread your wire down through it and pull snug so that the beads rest of the topside of the filigree. Come back up through the next hole (5th), pull snug, and repeat the same sequence you just did. Repeat this pattern until you are back where you started from. At this point, wrap the long tail in and out of a neighboring filigree hole until the wire is secure. Using flush cutters, cut both tails off.
- Now the easy part! Place a dab of E6000 glue in the center of your filigree. Place into the glue 1 Austrian crystal ss40 flatback rhinestone is black diamond. Let dry.
- All done! Enjoy your pretty new accessory.
WHAT YOU'LL NEED: (scroll down for purchase options)
- BCS-2112 - Czech Charlotte Seed Beads 13/0 Metallic Gold 1/2 Hank
Project uses 1 hank. You will need 1 package.
- BCZ-5319 - Preciosa Czech Crystal 3mm Bicone Beads Black Diamond AB (25)
Project uses 50 pieces. You will need 2 packages.
- BCZ-5410 - Preciosa Czech Crystal 4mm Bicone Beads 'Crystal Aurum' (50)
Project uses 20 pieces. You will need 1 package.
- FCO-9064 - Antiqued Brass Alligator Hair Clips With Filigree Flower Adornment - 2 Inch (4)
Project uses 2 pieces. You will need 1 package.
- SWF-44019 - Austrian Crystal, Round Flatback Rhinestone SS40 8.5mm, 8 Pieces, Black Diamond
Project uses 2 pieces. You will need 1 package.
- WNT-2833 - Beadsmith Tarnish Resistant Gold Color Copper Wire 28 Gauge 40 Yards (36.5 Meters)
Project uses 15 feet. You will need 1 package.
- XTL-1054 - E6000 Industrial Strength Glue Adhesive (0.18 fl oz)
Project uses 1 piece. You will need 1 package.
RECOMMENDED TOOLS:- XTL-5600 - Xuron Sharp Flush Cutter Pliers - Wire/Soft Flex