Retired - Urban Chic Necklace

PROJECT N676
Designer: Julie Bean
Skill Level: Beginner
This necklace is a play on shapes as it goes from larger Austrian crystal faux pearls to smaller ones and then back to larger ones again. Accenting the faux pearls, and adding a structural element to the design, are black finish hourglass-shaped strand spacers by Tierracast.
Instructions

Note: Components and tools listed within this INSTRUCTIONS box and the printer-friendly PDF, if available, may have been discontinued since this project was published. Refer to the PURCHASE COMPONENTS and TOOLS AND OTHER SUPPLIES sections for current availability.

  1. Start by cutting a 30 inch piece of black beading wire. Place a bead stopper 3 inches from the end.
  2. Place onto the beading wire:
  3. 1 gunmetal crimp bead
  4. 24 Austrian crystal crystal faux pearls 3mm in opaque jade green
  5. 7 Austrian crystal crystal faux pearls 4mm in opaque jade green
  6. 13 Austrian crystal crystal faux pearls 5mm in opaque jade green
  7. Next place onto your strand:
  8. 1 Tierracast black finish pewter 2-hole hourglass strand spacer
  9. 1 Austrian crystal crystal faux pearl 5mm in opaque jade green.
  10. Repeat this sequence 15 times (so you will have a total of 16 of these 2-hole strand spacers with a 5mm bead between each strung onto your strand).
  11. Next place onto your strand:
  12. 12 Austrian crystal crystal faux pearls 5mm in opaque jade green
  13. 7 Austrian crystal crystal faux pearls 4mm in opaque jade green
  14. 24 Austrian crystal crystal faux pearls 3mm in opaque jade green
  15. 1 gunmetal crimp bead
  16. Place another bead stopper on this end.
  17. Cut another 30 inch piece of black beading wire. Place a bead stopper 3 inches from the end.
  18. Place onto the beading wire:
  19. 1 gunmetal crimp bead
  20. 18 Austrian crystal crystal faux pearls 4mm in opaque jade green
  21. 4 Austrian crystal crystal faux pearls 5mm in opaque jade green
  22. 12 Austrian crystal crystal faux pearls 6mm in opaque jade green
  23. Now string your beading wire through the 2nd hole of one of the end Tierracast black finish pewter 2-hole hourglass strand spacers already strung on your first beaded strand (the one with bead stoppers now on each end). Next string on another Austrian crystal crystal faux pearl 6mm in opaque jade green. Repeat this step until you have a total of 4 6mm faux pearls between the strand spacers. Next string a total of 7 Austrian crystal crystal faux pearls 8mm in opaque jade green between the strand spacers. See photo. Now string on 4 more Austrian crystal crystal faux pearls 6mm in opaque jade green between the strand spacers. Now string 12 Austrian crystal crystal faux pearls 6mm in opaque jade green, 4 Austrian crystal crystal faux pearls 5mm in opaque jade green, 18 Austrian crystal crystal faux pearls 4mm in opaque jade green, and a gunmetal crimp bead. Place a bead stopper at the end.
  24. Lay your necklace out on the table so that you have the curve down at the bottom and the two strands of beads on each side laid out flat, untangled, and ready to be secured onto your strand reducers. See photo.
  25. Take one of your Tierracast black finish pewter 2 strand reducer bead bars, remove the bead stopper from one of your strand ends, loop the beading wire through one of the bottom holes on the strand reducer, go back through the crimp bead and several beads next to it, and then crimp the crimp bead. Cut of excess beading wire with your flush cutters. Repeat this step for the other beaded strand on this side of the necklace, securing it to the other hole at the bottom of the strand reducer.
  26. Go to the other side of your necklace and repeat this step, but be cautious to pull your wires snug so that there are no gaps between your beads and they form a nice curve down at the bottom where the Tierracast bead spacers are.
  27. Almost done!
  28. Cut a 22" piece of black beading wire. Place a bead stopper 3 inches from the end. Place onto this beading wire 1 gunmetal crimp bead, 1 3mm faux pearl, 1 6mm faux pearl, 1 Tierracast black finish pewter 4mm faceted cube spacer bead, another 6mm faux pearl, another 4mm cube spacer bead, 2 6mm faux pearls, another 4mm spacer bead, 5 6mm faux pearls, a 6mm cube spacer bead, 18 8mm faux pearls, a 6mm cube spacer bead, 5 6mm faux pearls, another 4mm spacer bead, 2 6mm faux pearls, another 4mm cube spacer bead, another 6mm faux pearl, another 4mm faceted cube spacer bead, a 6mm faux pearl, a 3mm faux pearl, and a gunmetal crimp bead.
  29. Secure the wire end to the top loop of your strand reducer via the crimp bead. Crimp the bead. Go to the other side of your strand, remove the bead stopper, and secure this end to the other strand reducer (again via the crimp bead attaching it to the top loop). Crimp the bead and cut off any excess wire with flush cutters.
  30. All done!
WHAT YOU'LL NEED: (scroll down for purchase options)
  • FCR-1253 - Gun Metal Brass Crimp Beads 2mm x 1.5mm (100)
    Project uses 6 pieces. You will need 1 package.

  • XCR-67553 - Beadalon Wire Black 7 Strand .015 Inch / 30Ft
    Project uses 7 feet. You will need 1 package.

  • BMB-5660 - TierraCast Black Finish Pewter Lead-Free 2 Hole Hourglass Strand Spacer Beads 18.5mm (2)
    Project uses 16 pieces. You will need 8 packages.

  • BMB-3155 - TierraCast Black Finish Lead-Free Pewter 4mm Faceted Cube Spacer Beads (4)
    Project uses 6 pieces. You will need 1 package.

  • SWP-3090 - Austrian Crystal, 5810 Round Faux Pearl Beads 3mm, 50 Pieces, Jade
    Project uses 50 pieces. You will need 1 package.

  • SWP-6090 - Austrian Crystal, 5810 Round Faux Pearl Beads 6mm, 50 Pieces, Jade
    Project uses 50 pieces. You will need 1 package.

  • SWP-4090 - Austrian Crystal, 5810 Round Faux Pearl Beads 4mm, 50 Pieces, Jade
    Project uses 50 pieces. You will need 1 package.

  • SWP-8090 - Austrian Crystal, 5810 Round Faux Pearl Beads 8mm, 25 Pieces, Jade
    Project uses 25 pieces. You will need 1 package.

  • FCO-3705 - TierraCast Black Finish Lead-Free Pewter 2-Strand Reducer Bead Bars 10.6mm (2)
    Project uses 2 pieces. You will need 1 package.

RECOMMENDED TOOLS:
  • XTL-5200 - Standard Size Beading Crimping Pliers (For 2x2mm & 2x1mm Crimp Beads)
  • XTL-5600 - Xuron Sharp Flush Cutter Pliers - Wire/Soft Flex
  • XTL-3000 - Bead Stopper- Stop Beads Sliding Off Stringing Material
Additional Information
Theme As Seen In
Ingredients FCR-1253, FCO-3705,

Purchase Components

Purchase the components needed to make this project. Change quantities as needed to make multiple pieces. This project is RETIRED. Please review project instructions carefully—some items may no longer be available for this project and will not be listed below. Tip: Save this project to your wishlist to easily return to project instructions.
Crimp Beads, 2x1.5mm, Gunmetal (100 Pieces)
You will need 1 package(s).
1 package = 100 Pieces.
$1.45 / Package | SKU: FCR-1253
You will need 1 package(s).
1 package = .
/ Package | SKU: FCO-3705
Earn Reward Points Earn Reward Points with your purchase of project components or tools.

Tools and Other Supplies:

Related Video [VIEW ALL VIDEOS]

Accessible Options For closed captions/subtitles, click the CC icon on the video player after starting the video.

You recently viewed

Clear recently viewed