Retired - 'Scrabble' Tile Pendant Using 2-Part Resin

Note: Components and tools listed within this INSTRUCTIONS box and the printer-friendly PDF, if available, may have been discontinued since this project was published. Refer to the PURCHASE COMPONENTS and TOOLS AND OTHER SUPPLIES sections for current availability.

1. Watch the step by step video on making 'Scrabble' tile pendants!
2. A couple notes to start with: Not listed in the ingredients, you will need a disposable plastic mixing cup and a stir stick such as a popsicle stick. Also, we are using a wood tile which is 1" square, this is slightly larger then a Scrabble tile. If you have a Scrabble tile, feel free to use that.
3. To begin, choose your image. This can be a photo, a clipping out of a magazine, some handmade paper, a print off your computer, anything you like. We have chosen a bird design from the "Song Birds" collage sheet. Unless you have used a computer to EXACTLY size your image to be 1" square, then cut out your image leaving some extra room on all sides except for the top.
4. Using your finger or a small paint brush, spread an even layer of Nunn Glue along the back side of the image. Line the top of the wood tile up with the top of your image (this is why you did not leave excess room on the top of your image when you cut it out) and center it so that you capture the part of the image you are most interested in. Press into place and use your fingers to smooth out any excess air bubbles. Allow to dry.
5. Once dry, carefully cut along the edges so that the paper is flush with your wood. Use your fingers or a clean paint brush to apply an even layer of Mod Podge over the top of the image/tile. Let dry.
6. Mix your Ice Resin and using your stir stick (not pouring), apply a dime size amount in the middle of your tile over the top of the image. Starting from the "glob" of resin in the center, take your stir stick and push it towards the edges. Work slowly and carefully, just keep pushing the resin to the edges -the surface tension will keep the resin from going over the edge if you carefully push it. If you need to add more resin, add it to the middle again, do not try to add it to the outer edges. Once happy with your resin, leave it for about 15 minutes and then come back to check for air bubbles. If you find air bubbles, remove them with a heat source such as a micro torch. Let cure for a full 3 days.
7. Turn your now fully hardened pendant upside down. Using a toothpick or small piece of wire as an applicator, place a small amount of E6000 on the flat glue-on side of your Aanraku pendant bail. Center on the back side of your tile and press into place. Let dry.
8. String your ball chain through the bail loop. If you purchased a pre-made ball chain necklace, it will already have the connector clasp on one end. If you purchased ball chain by the foot and a connector clasp separately, cut the ball chain to the desired length and "snap" the connector clasp into place.
9. Enjoy your fun new necklace!

• BWD-9000 - Natural Wood Square Collage Jewelry Pendant Tiles 25mm (1 Inch) 24 Tiles
  Project uses 1 piece. You will need 1 package.


• XTL-9504 - Nunn Design Collage Sheet Song Birds For Scrapbook - Fits Patera
  Project uses 1 piece. You will need 1 package.


• FCO-4242 - Aanraku, Heart Shaped Glue-On Pendant Bails, Large, 10 Pieces, Silver Plated
  Project uses 1 piece. You will need 1 package.


• AXC-91601 - Black Coated Steel 2mm Ball Chain Necklace 16 Inches
  Project uses 1 piece. You will need 1 package.


• XTL-1054 - E6000 Industrial Strength Glue Adhesive (0.18 fl oz)
  Project uses 1 piece. You will need 1 package.


• XTL-1031 - Nunn Design Glue Adhesive 2 oz. - For Patera Findings (1)
  Project uses 1 piece. You will need 1 package.


• XTL-1041 - Mod Podge Gloss All-In-One Decoupage Sealer / Glue / Finish (4 fl. oz. )
  Project uses 1 piece. You will need 1 package.


• TRC-12 - Ice Resin Epoxy, Jewelers Grade Clear Casting Kit, 1 Ounce
  Project uses 1 piece. You will need 1 package.

• XTL-5700 - Fiskars 5 Precision Tip Scissors - Super Sharp
• XTL-0300 - Jeweller's Micro-Flame Butane Torch Self Igniting Refillable 6 Inch