Retired - Pink Champagne Bracelet

Designer: Karlin Jones
Skill Level: Intermediate
If champagne bubbles could be threaded onto a bracelet, they would look like this strand of vintage Lucite beads in an effervescent peachy pink. Paired with bright silver plated findings, this bracelet has a wonderful touch of vintage flair.

Note: Components and tools listed within this INSTRUCTIONS box and the printer-friendly PDF, if available, may have been discontinued since this project was published. Refer to the PURCHASE COMPONENTS and TOOLS AND OTHER SUPPLIES sections for current availability.

These instructions will make a finished bracelet that is approximately 8" long. Measure your wrist and cut your silver plated wire shorter or longer to adjust the length. Be sure to include at least 6 additional inches of wire to allow for crimping, three inches for each side.
  1. Cut 14 inches of silver plated wire with your flush cutters and string the tip through a crimp bead.
  2. String on your clasp (through the small loop on the side) then loop the beading wire back through the crimp bead (you want a short tail of about 3 inches of wire). Pull snug so that you have a small loop. Crimp the crimp bead.
  3. Now, you will begin stringing on your beads and bead caps. Do not snip off the short tail of the wire because you will be stringing on your first few beads and bead caps through it as well. (This step is to ensure that your wire is secure.)
  4. String on one bead cap, then one pink Lucite bead, and then another bead cap onto your wire. Your pink Lucite bead should be sandwiched between the two filigree bead caps.
  5. Repeat this sequence 9 more times.
  6. Once you've strung all your beads, take the end of your wire and string it through another crimp bead and the loop on the clasp on the other side. Also feed your wire through a few adjacent beads. (When you are doing this, also make sure to not tug too tightly.)
  7. Using your crimp pliers, crimp your crimp bead. Snip off any excess beading wire from the short tail that is showing.
  8. Lastly, take a crimp cover, slide it onto your crimped crimp bead, and carefully tighten it with your chain nose pliers. Repeat this step again with the crimped bead on the other side.
  9. Your bracelet is now ready.
WHAT YOU'LL NEED: (scroll down for purchase options)
  • XCR-69513 - Beadalon Wire Standard Bright 19 Strand .015 Inch / 30Ft
    Project uses 14 inches. You will need 1 package.

  • BPL-1083 -
    Project uses 10 pieces. You will need 1 package.

  • FCL-5592 - Silver Plated Sleek Oval Large Box Clasp - 17mm x 12mm (X5)
    Project uses 1 set. You will need 1 package.

  • BMB-7074 - Silver Plated Ornate Filigree Bead Caps 14mm (20)
    Project uses 20 pieces. You will need 1 package.

  • FCR-1210 - Beadalon Silver Plated Crimp Beads 1.3mm (95 Beads)
    Project uses 2 pieces. You will need 1 package.

  • FCR-1054 - Shiny Silver Tone Crimp Bead Covers 4mm (x144)
    Project uses 2 pieces. You will need 1 package.

  • XTL-5600 - Xuron Sharp Flush Cutter Pliers - Wire/Soft Flex
  • XTL-5200 - Standard Size Beading Crimping Pliers (For 2x2mm & 2x1mm Crimp Beads)
  • XTL-5511 - Beadsmith Jeweller's Micro Pliers Chain Nose Flat Nose
Additional Information
Theme Summer, Spring, Special Occasion, Bridal, Autumn
Ingredients XCR-69513, BPL-1083, FCL-5592, BMB-7074, FCR-1210, FCR-1054,

Purchase Components

Purchase the components needed to make this project. Change quantities as needed to make multiple pieces. This project is RETIRED. Please review project instructions carefully—some items may no longer be available for this project and will not be listed below. Tip: Save this project to your wishlist to easily return to project instructions.
Beadalon Wire Standard Bright 19 Strand .015 Inch / 30Ft
You will need 1 package(s).
1 package = 1 Spool.
$11.99 / Package | SKU: XCR-69513
Silver Plated Ornate Filigree Bead Caps 14mm (20 pcs)
You will need 1 package(s).
1 package = 20 Pieces.
$4.69 / Package | SKU: BMB-7074
Beadalon Crimp Beads, 1.3mm, Silver Plated (95 Pieces)
You will need 1 package(s).
1 package = 95 Pieces.
$3.75 / Package | SKU: FCR-1210
Crimp Bead Covers, 4mm, Silver Tone (144 Pieces)
You will need 1 package(s).
1 package = 144 Pieces.
$8.45 / Package | SKU: FCR-1054
Earn Reward Points Earn Reward Points with your purchase of project components or tools.

Tools and Other Supplies:

Sharp Flush Cutter Pliers - For Cutting Beading Wire (1 Piece)
The Beadsmith Jeweller's Micro Pliers Chain Nose Flat Nose

Related Video [VIEW ALL VIDEOS]

Accessible Options For closed captions/subtitles, click the CC icon on the video player after starting the video.

You recently viewed

Clear recently viewed