Retired - Purple Faux Lariat Necklace

PROJECT N193
Designer: Andrea Morici
Skill Level: Beginner
Extra long and luxe, this faux lariat features Austrian crystals and Austrian crystal pearls in multiple luscious shades of purple.
Instructions

Note: Components and tools listed within this INSTRUCTIONS box and the printer-friendly PDF, if available, may have been discontinued since this project was published. Refer to the PURCHASE COMPONENTS and TOOLS AND OTHER SUPPLIES sections for current availability.

  1. Cut a piece of the gunmetal double curb chain that is roughly three inches in length. Set this aside.
  2. Cut two pieces of the black artistic wire at five inches long each. Cut a third piece of black artistic wire at one foot long.
  3. Onto each of the five inch long pieces of black artistic wire, create the beginning of a large wrapped wire loop. Before completing the loops, thread them through the jet cosmic ring pendant. Complete both wrapped wire loops and trim off excess wire.
  4. Onto each of the two pieces five inch long black artistic wire (now attached to the cosmic ring pendant), thread an 8mm dark purple Austrian crystal faux pearl. Create another wrapped wire loop at the opposite end of both pieces of wire and trim off excess.
  5. Thread the one foot long piece of black artistic wire through the Austrian crystal amethyst baroque pendant, so that the pendant is about halfway down the wire. Create a ninety degree bend in the wire right next to the pendant, so that one half of the wire points upward. Wrap the half of the wire that is protruding from the side tightly around the pendant until the wrapping reaches from the hole to the very tip of the pendant, and wraps around the other half of the wire a few times.
  6. Onto the half of the wire that is sticking upward, thread an 8mm dark purple Austrian crystal faux pearl. Create the beginning of a large wrapped wire loop. Before completing the loop, thread it through the jet cosmic ring pendant. Complete the wrapped wire loop and trim off excess wire.
  7. Cut a piece of fine beading wire that is one foot long. Secure one end of this wire with a Bead Stopper.
  8. Onto the wire thread the following:
  9. a 5mm jet Austrian crystal crystal spacer bead
  10. an 8mm amethyst Austrian crystal crystal round bead
  11. a 5mm jet Austrian crystal crystal spacer bead
  12. an 8mm burgundy Austrian crystal faux pearl
  13. a 5mm jet Austrian crystal crystal spacer bead
  14. an 8mm dark purple Austrian crystal faux pearl
  15. a 5mm jet Austrian crystal crystal spacer bead
  16. an 8mm burgundy Austrian crystal faux pearl
  17. a 5mm jet Austrian crystal crystal spacer bead
  18. an 8mm dark purple Austrian crystal faux pearl.
  19. Repeat this stringing pattern one more time. At the end, add:
  20. a 5mm jet Austrian crystal crystal spacer bead
  21. one more 8mm amethyst Austrian crystal crystal round bead
  22. one more 5mm jet Austrian crystal crystal spacer bead
  23. Onto the end of the strand, thread a gunmetal crimp bead, but do not crimp it yet. Thread the end of the strand through the wrapped wire loop on one of the dark purple faux pearl links connected to the cosmic ring. Thread the strand back through the crimp tube, pull snug, and crimp.
  24. Remove the Bead Stopper from the opposite end of the strand. Once again, thread a crimp bead, but do not crimp it yet. Thread the end of the strand through a double link at one end of the long piece of double curb chain. Thread the strand back through the crimp tube, pull snug, and crimp.
  25. Open a gunmetal jump ring and thread it through the other end of the long piece of double curb chain, and also through the wrapped wire loop on the other dark purple faux pearl link connected to the cosmic ring. Close this jump ring once more.
  26. Thread an 8mm burgundy faux pearl onto a gunmetal headpin and create a wrapped loop on the end. Trim off excess wire.
  27. Open two more gunmetal jump rings. Thread one of these jump rings through the wrapped wire loop at the top of the burgundy pearl drop and also through the double link at one end of the three inch long piece of double curb chain. Close this jump ring.
  28. Thread the other jump ring through the other end of the three inch long piece of double curb chain and also through the large wrapped loop containing the dark purple faux pearl and the amethyst baroque pendant. Close this jump ring.
  29. Finally, place a crimp bead cover over each of the crimp beads, and gently squeeze them shut.
WHAT YOU'LL NEED: (scroll down for purchase options)
  • CHA-9717 - Gun Metal Finish Steel Parallel Link Curb Chain 7mm Bulk By The Foot
    Project uses 2 feet. You will need 2 packages.

  • FJR-5296 - Gun Metal Plated Open Jump Rings 6mm 19 Gauge (100)
    Project uses 3 pieces. You will need 1 package.

  • FCR-1083 - Gun Metal Brass Fluted Crimp Bead Covers 4mm (144)
    Project uses 2 pieces. You will need 1 package.

  • FCR-1253 - Gun Metal Brass Crimp Beads 2mm x 1.5mm (100)
    Project uses 2 pieces. You will need 1 package.

  • FHP-5421 - Gun Metal Head Pins 2 Inches 24 Gauge (X50)
    Project uses 1 piece. You will need 1 package.

  • WCR-2403 - Artistic Wire, Copper Craft Wire 24 Gauge Thick, 10 Yard Spool, Permanent Black Color
    Project uses 2 feet. You will need 1 package.

  • XCR-5143 - Soft Flex, 21 Strand Fine Beading Wire .014 Inch Thick, 30 Feet, Satin Silver
    Project uses 1 foot. You will need 1 package.

  • SWC-9025 - Austrian Crystal, 4139 Cosmic Ring Pendant 20mm, 1 Piece, Jet
    Project uses 1 piece. You will need 1 package.

  • SWC-9296 - Austrian Crystal, 6090 Baroque Pendant 22x15mm, 1 Piece, Amethyst
    Project uses 1 piece. You will need 1 package.

  • SWP-8024 -
    Project uses 7 pieces. You will need 1 package.

  • SWP-8023 - Austrian Crystal, 5810 Round Faux Pearl Beads 8mm, 25 Pieces, Burgundy
    Project uses 5 pieces. You will need 1 package.

  • SWC-0896 - Austrian Crystal, 5000 Round Beads 8mm, 8 Pieces, Amethyst
    Project uses 3 pieces. You will need 1 package.

  • SWC-5202 - Austrian Crystal, 5305 Rondelle Spacer Beads 5mm, 12 Pieces, Jet
    Project uses 12 pieces. You will need 1 package.

RECOMMENDED TOOLS:
  • XTL-3000 - Bead Stopper- Stop Beads Sliding Off Stringing Material
Additional Information
Ingredients FJR-5296, FCR-1083, FCR-1253, WCR-2403, XCR-5143,

Purchase Components

Purchase the components needed to make this project. Change quantities as needed to make multiple pieces. This project is RETIRED. Please review project instructions carefully—some items may no longer be available for this project and will not be listed below. Tip: Save this project to your wishlist to easily return to project instructions.
Gun Metal Plated Open Jump Rings 6mm 19 Gauge (100 pcs)
You will need 1 package(s).
1 package = 100 Pieces.
$5.99 / Package | SKU: FJR-5296
Crimp Bead Covers, Fluted 4mm, Gunmetal Plated (144 Pieces)
You will need 1 package(s).
1 package = 144 Pieces.
$7.45 / Package | SKU: FCR-1083
Crimp Beads, 2x1.5mm, Gunmetal (100 Pieces)
You will need 1 package(s).
1 package = 100 Pieces.
$1.45 / Package | SKU: FCR-1253
Artistic Wire, Copper Craft Wire 24 Gauge Thick, Permanent Black Color (10 Yard Spool)
You will need 1 package(s).
1 package = 1 Spool.
$4.47 / Package | SKU: WCR-2403
Soft Flex, 21 Strand Fine Beading Wire .014 Inch Thick, Satin Silver (30 Feet)
You will need 1 package(s).
1 package = 1 Spool.
$14.69 / Package | SKU: XCR-5143
Earn Reward Points Earn Reward Points with your purchase of project components or tools.

Tools and Other Supplies:

Related Video [VIEW ALL VIDEOS]

Accessible Options For closed captions/subtitles, click the CC icon on the video player after starting the video.

You recently viewed

Clear recently viewed