Pink Colette Bridesmaid Bracelet

Note: Components and tools listed within this INSTRUCTIONS box and the printer-friendly PDF, if available, may have been discontinued since this project was published. Refer to the PURCHASE COMPONENTS and TOOLS AND OTHER SUPPLIES sections for current availability.

1. Cut two 12" lengths of .014" Soft Flex beading wire.
2. Hold the two lengths together and attach a bead stopper 2-3" from one end.
3. With the two lengths of wire together, string one 3 mm silver plated round bead followed by two 4 mm silver plated daisy spacer beads.
4. Next, string one 2 mm x 38 mm silver plated curved noodle tube bead onto each of the lengths of wire.
5. Bring the lengths of wire together and string two daisy spacer beads.
6. Then, with the lengths together, string one 4 mm PRESTIGE Crystal round bead, one 5.7 mm silver plated leaf bead cap, one 8 mm rosaline PRESTIGE Pearl bead, and another leaf bead cap. Make sure that the bead caps are strung with the wide side facing the pearl bead.
7. Repeat step 6 three times, and then, with the lengths together, string one crystal bead and then two daisy spacer beads.
8. Next, string one 2 mm x 38 mm silver plated curved noodle tube bead onto each of the lengths of wire.
9. Bring the lengths back together and string two daisy spacer beads followed by one silver plated round bead.
10. String a 1.3 mm silver plated crimp bead onto the end of your bracelet, with the lengths together. Then use a .024" silver plated wire and thread protector to attach one side of the 12 mm silver plated toggle clasp. Bring the strands of wire back through the crimp bead and silver plated round bead and use chain nose pliers to pull tight. Secure with the crimp bead and trim the excess wire with flush cutters.
11. Carefully remove the bead stopper from the other end of your work. String a crimp bead onto the end, with the lengths together, and use another wire and thread protector to attach the other side of the toggle clasp. Bring the strands of wire back through the crimp bead and silver plated round bead and use chain nose pliers to pull tight. Secure with the crimp bead and trim the excess wire with flush cutters.

• BMB-3215 - TierraCast Fine Silver Plated Pewter Daisy Spacer Beads 4mm (x 50)
  Project uses 8 pieces. You will need 1 package.


• BMB-3269 - TierraCast Fine Silver Plated Pewter Leaf Bead Caps 5.7mm (x 4)
  Project uses 6 pieces. You will need 2 packages.


• BMB-4072 - Silver Plated Curved Noodle Tube Beads 2mm x 38mm (12)
  Project uses 4 pieces. You will need 1 package.


• BMB-5052 - Silver Plated 3mm Round Metal Beads (100)
  Project uses 2 pieces. You will need 1 package.


• FCL-7033 - TierraCast Silver Plated Pewter Sleek Wrap Toggle Clasp 12mm
  Project uses 1 piece. You will need 1 package.


• FCR-1210 - Beadalon Silver Plated Crimp Beads 1.3mm (95 Beads)
  Project uses 2 pieces. You will need 1 package.


• FCR-4165 - Silver Plated Wire & Thread Protectors .024 Inch Loops (50)
  Project uses 2 pieces. You will need 1 package.


• PRES-5000-CRYS4 - PRESTIGE Crystal, #5000 Round Bead 4mm, Crystal (1 Piece)
  Project uses 4 pieces. You will need 4 packages.


• PRES-5810-ROSE8 - PRESTIGE Crystal, #5810 Round Pearl Bead 8mm, Rosaline (1 Piece)
  Project uses 3 pieces. You will need 3 packages.


• XCR-5143 - Soft Flex, 21 Strand Fine Beading Wire .014 Inch Thick, 30 Feet, Satin Silver
  Project uses 2 feet. You will need 1 package.

• XTL-3000 - Bead Stopper- Stop Beads Sliding Off Stringing Material
• XTL-5600 - Xuron Sharp Flush Cutter Pliers - Wire/Soft Flex
• XTL-5230 - Double Notch Crimping Pliers - Works on 2mm And 3mm Crimps
• XTL-5511 - Beadsmith Jeweller's Micro Pliers Chain Nose Flat Nose