Note: Components and tools listed within this INSTRUCTIONS box and the printer-friendly PDF, if available, may have been discontinued since
this project was published. Refer to the PURCHASE COMPONENTS and TOOLS AND OTHER SUPPLIES sections for current availability.
- Begin by cutting five pieces of Power Pro braided beading thread at two feet long each. Join all of the strands together and secure one end to prevent accidental bead spillage. We recommend using a Bead Stopper for this.
- Separate one strand of Power Pro and thread it through a needle. Pull the thread through the eye of the needle about two inches and fold down.
- Onto that needle, thread one inch of seed beads. Make sure that you stagger the colors so that the pattern of the beads is random.
- Remove the needle from that strand, and add it to one of the other strands of Power Pro. Thread one inch of seed beads onto this strand. Do the same with the other strands of Power Pro so that there is one inch of mixed seed beads on each piece of thread.
- Gather all five strands together and thread all of them through a single hematite fire polish bead, a coffee bean bead, and another hematite fire polish bead.
- Separate the five strands and thread one inch of seed beads onto each strand once again.
- Gather all five strands together again and thread all of them through a single hematite fire polish bead, a coffee bean bead, and another hematite fire polish bead.
- Repeat this process of adding an inch of seed beads to each individual strand and the hematite, coffee bean, hematite combination to the combined threads until you have five segments of seed beads.
- When you complete the fifth segment of seed beads, gather all five strands together once again and thread them through the following beads: a hematite fire polish, a coffee bean, four more hematite fire polish beads, another coffee bean bead, and finally one more hematite fire polish. This will be the center of your necklace where the coffee cup pendant will hang.
- Repeat steps six through eight to complete the other half of the necklace.
- After you have threaded the last segment of seed beads, gather all the strands together once more and thread a crimp bead onto them, but do not crimp yet.
- Thread all five strands through the loop of an eyepin and back through the crimp bead and crimp down. Trim off excess thread.
- Remove the Bead Stopper from the other end of the necklace and repeat the last two steps.
- Now you have an eyepin at each end of the necklace. Onto each eyepin thread a coil rondelle, six gunmetal jump rings a coffee bean bead and a closed crimp bead cover.
- Create a simple loop at the end of each eyepin and trim off excess wire.
- To one end of the necklace, add a gunmetal jump ring. To the other, add the lobster clasp.
WHAT YOU'LL NEED: (scroll down for purchase options)
- PND-9258 -
Project uses 1 piece. You will need 1 package.
- BCP-3485 - Czech Fire Polished Glass Beads 4mm Round 'Hematite' (50)
Project uses 22 pieces. You will need 1 package.
- BCP-9040 - Czech Glass Beads Reddish Brown Coffee Beans Espresso (25)
Project uses 12 pieces. You will need 1 package.
- BCS-1393 - Czech Seed Beads Mix Lot 11/0 Chocolate Mud Pie Brown Yum
Project uses 50 inches. You will need 1 package.
- FJR-5296 - Gun Metal Plated Open Jump Rings 6mm 19 Gauge (100)
Project uses 14 pieces. You will need 1 package.
- BMB-3500 - TierraCast Fine Silver Plated Pewter Coil Edge Spacer Beads 5mm (10)
Project uses 2 pieces. You will need 1 package.
- FHP-6270 - Gunmetal Grey Brass Open Eye Pins 21 Gauge 2 Inch (x50)
Project uses 2 pieces. You will need 1 package.
- FCL-2511 - Gunmetal Plated Curved Lobster Clasps 8mm (10)
Project uses 1 piece. You will need 1 package.
- FCR-1210 - Beadalon Silver Plated Crimp Beads 1.3mm (95 Beads)
Project uses 2 pieces. You will need 1 package.
- FCR-1053 - Shiny Silver Tone Crimp Bead Covers 3mm (x144)
Project uses 2 pieces. You will need 1 package.
- XCR-1162 - Power Pro Braided Beading Thread .006 Inch White - 28 Yds
Project uses 10 feet. You will need 1 package.
- XTL-3010 - Beading Needles For Soft Touch .010 16 Needles Size 10
Project uses 1 piece. You will need 1 package.
RECOMMENDED TOOLS:- XTL-3000 - Bead Stopper- Stop Beads Sliding Off Stringing Material