Retired - Butterfly Bottle Cap Necklace

PROJECT N627
Designer: Julie Bean
Skill Level: Intermediate
Who doesn't love butterflies, bottle caps, and glitter? We sure love all three and have married them in this fun necklace. Make just one or make many to share with friends.
Instructions

Note: Components and tools listed within this INSTRUCTIONS box and the printer-friendly PDF, if available, may have been discontinued since this project was published. Refer to the PURCHASE COMPONENTS and TOOLS AND OTHER SUPPLIES sections for current availability.

  1. Note: if you want to use glitter, pick some up before starting this project. Any color you like, the smaller the flakes, the more delicate the overall look.
  2. Flatten a bottle cap using a rubber mallet and steel bench block.
  3. Remove the liner from the bottle cap.
  4. Take your metal hole punch pliers and punch a hole at the top of your bottle cap, inside the "ruffles".
  5. Pick a butterfly from your collage sheet. You will want to use an image that is at least 1" in diameter. Cut out the image. To get the right size circle, you can either use something which is around 1" in diameter such as US quarter (just a smidge smaller then 1") or I used a 1" metal stamping blank. You can also trace around the edge of your bottle cap and then cut your circle down until it fits inside.
  6. Coat the entire backside of your image with a layer of Nunn glue. Press into the center of your flattened bottle cap, use your fingers to smooth out any air bubbles. Let dry.
  7. Using a paint brush, paint a layer of Mod Podge over the top of your image. Let dry and clean out your paint brush.
  8. Using a toothpick or piece of wire as an applicator, run a thin line of Nunn glue along the interior edge of your bottle cap, all the way around the circle. Immediately shake glitter over the glue. Let dry and then shake and blow off any loose glitter. If you need to "dust" off your image to get any glitter off the center of the image, just do so with a dry paint brush or your fingers.
  9. Fill your bottle cap bezel with Gel du Soleil. Do not overfill. Let settle for a few minutes to see if any bubbles rise to the surface. If bubbles arise, use a heat source such as a micro torch to remove them (just swipe the heat source over the top, not touching and not standing still). Place in the UV light for 15 minutes.
  10. Remove your bottle cap from the UV light. Open a 6mm jump ring and link it through the punched hole at the top of your bottle cap. Close the jump ring.
  11. Take your ball chain and cut it to the desired length. You can leave the chain uncut at 2 feet, making your necklace 24" long or you can cut it shorter, it's up to you.
  12. Place a ball chain connector clasp on one end of the necklace. If you want to close the necklace, just link the other end of the ball chain through the connector clasp.
  13. Have fun making lots of these!
WHAT YOU'LL NEED: (scroll down for purchase options)
  • XTL-9537 - Nunn Design Collage Sheet Various Butterflies For Scrapbook - Fits Patera
    Project uses 1 piece. You will need 1 package.

  • PND-2042 - Sky Blue Crown Bottle Caps Craft Scrapbook Jewelry No Liners (50)
    Project uses 1 piece. You will need 1 package.

  • XTL-1017 - Gel Du Soleil UV Epoxy Dimensional Gloss for Crafts & Jewelry 0.3 Fl. Oz.
    Project uses 1 piece. You will need 1 package.

  • XTL-1041 - Mod Podge Gloss All-In-One Decoupage Sealer / Glue / Finish (4 fl. oz. )
    Project uses 1 piece. You will need 1 package.

  • XTL-1031 - Nunn Design Glue Adhesive 2 oz. - For Patera Findings (1)
    Project uses 1 piece. You will need 1 package.

  • FJR-3094 - Antiqued Silver Plated Open Jump Rings 6mm 18 Gauge (50)
    Project uses 1 piece. You will need 1 package.

  • CHA-2001 - Genuine Stainless Steel Ball Chain 2.4mm - Bulk Sold By The Foot
    Project uses 2 feet. You will need 2 packages.

  • FCL-2001 - Stainless Steel Ball Chain Connector Clasps - Fits 2.4mm (10)
    Project uses 1 piece. You will need 1 package.

RECOMMENDED TOOLS:
  • XTL-0060 - Eurotool EuroPunch 1.25mm Round Hole Punch Pliers For Sheet Metal
  • XTL-0258 - Mini Rubber And Steel Bench Block For Metal Working And Wire Hardening
  • XTL-0247 - Eurotool Hammer Rubber Mallet For Metal Smithing - 8 Ounces
  • XTL-1510 - Lisa Pavelka Magic Gloss 9 watt UV Resin Curing Light
Additional Information
Ingredients XTL-1017, XTL-1041, XTL-1031, FJR-3094, CHA-2001, FCL-2001,

Purchase Components

Purchase the components needed to make this project. Change quantities as needed to make multiple pieces. This project is RETIRED. Please review project instructions carefully—some items may no longer be available for this project and will not be listed below. Tip: Save this project to your wishlist to easily return to project instructions.
Gel Du Soleil UV Epoxy Dimensional Gloss for Crafts & Jewelry 0.3 Fl. Oz.
You will need 1 package(s).
1 package = 3 Fl. oz.
$12.99 / Package | SKU: XTL-1017
Mod Podge Gloss All-In-One Decoupage Sealer / Glue / Finish (4 fl. oz. )
You will need 1 package(s).
1 package = 4 fl. oz..
$6.89 / Package | SKU: XTL-1041
You will need 1 package(s).
1 package = .
/ Package | SKU: XTL-1031
Antiqued Silver Plated Open Jump Rings 6mm 18 Gauge, (50 Pieces)
You will need 1 package(s).
1 package = Each.
$2.59 / Package | SKU: FJR-3094
Stainless Steel Ball Chain 2.4mm, by the Foot
You will need 2 package(s).
1 package = By the Foot.
$0.63 / Package | SKU: CHA-2001
Connector Clasps, Fits 2.4mm Ball Chain, Stainless Steel (10 Pieces)
You will need 1 package(s).
1 package = 10 Pieces.
$1.99 / Package | SKU: FCL-2001
Earn Reward Points Earn Reward Points with your purchase of project components or tools.

Tools and Other Supplies:

Eurotool EuroPunch 1.25mm Round Hole Punch Pliers For Sheet Metal
Eurotool Hammer Rubber Mallet For Metal Smithing - 8 Ounces

Related Video [VIEW ALL VIDEOS]

Accessible Options For closed captions/subtitles, click the CC icon on the video player after starting the video.

You recently viewed

Clear recently viewed