Retired - Andalucia Earrings

Name: Retired - Andalucia Earrings
Brand: Beadaholique
SKU: E3043
Availability: OutOfStock

PROJECT E3043

Designer: Karlin Jones

Skill Level: Intermediate

Save to Wishlist

Printer Friendly PDF
(if available)

With an ornate stamping embellished with Turquoise Czech crystal rhinestone cup chain and enhanced using Vintaj patina in Verdigris Teal, these earrings will add a fresh pop of color to your look.

Instructions

Note: Components and tools listed within this INSTRUCTIONS box and the printer-friendly PDF, if available, may have been discontinued since this project was published. Refer to the PURCHASE COMPONENTS and TOOLS AND OTHER SUPPLIES sections for current availability.

By following the instructions below, you will make one earring. Repeat all instructions to make the second earring. You will need a clean work space and a paint brush for this project.

Using your paint brush, begin dabbing the surface of your antiqued silver plated stamping with your two Vintaj patinas. Wash your brush in between uses and colors. Try not to blend the two colors together, instead cover the stamping with the two colors in separate areas. See photo.
While your stamping is still wet, use the side of your Vintaj relief block to sand the raised areas of your stamping. Set aside to dry.
Cut a 1 inch length of your Turquoise Czech glass cup chain with your flush cutters.
Once your stamping is dry, add a thin line of Hypo Cement glue in a �V� design in the center of your stamping. See photo for glue placement assistance.
Carefully pick up your cup chain length and place it down onto the glue line. Please see photo to get exact placement. Set aside to dry for a few minutes.
Once dry, use your chain nose pliers to open your antiqued silver plated earring hook (how you would a jump ring) and slide on the loop at the top of your stamping. Close the hook back up.
You're done!

WHAT YOU'LL NEED: (scroll down for purchase options)

CHA-10120 - Czech Crystal Silver Plated Rhinestone Cup Chain 18PP Turquoise (By The Foot)
Project uses 2 inches. You will need 1 package.

PND-5707 - Antiqued Silver Plated Ornate Etruscan Drop Filigree Stamping 55mm (1)
Project uses 2 pieces. You will need 2 packages.

XTL-1001 - G S Hypo Cement Precise Applicator Essential!
Project uses 1 piece. You will need 1 package.

FEA-3081 - Antiqued Silver Plated French Wire Earring Hooks 16mm (25 Pairs)
Project uses 2 pieces. You will need 1 package.

XTL-9067 - Vintaj Patina Opaque Permanent Ink - Moss Green - 0.5 Ounce Bottle
Project uses 1 piece. You will need 1 package.

XTL-9073 - Vintaj Patina Opaque Permanent Ink - Verdigris Teal - 0.5 Ounce Bottle
Project uses 1 piece. You will need 1 package.

RECOMMENDED TOOLS:

XTL-2222 - Vintaj Metal Relief Block For Filing, Buffing & Sanding
XTL-5600 - Xuron Sharp Flush Cutter Pliers - Wire/Soft Flex
XTL-5511 - Beadsmith Jeweller's Micro Pliers Chain Nose Flat Nose

Additional Information

Ingredients

CHA-10120, XTL-1001,

Purchase Components

Purchase the components needed to make this project. Change quantities as needed to make multiple pieces. This project is RETIRED. Please review project instructions carefully—some items may no longer be available for this project and will not be listed below. Tip: Save this project to your wishlist to easily return to project instructions.

            
You will need 1 package(s).
1 package = .

             / Package | SKU: CHA-10120

G S Hypo Cement Precise Applicator Essential!

            G S Hypo Cement Precise Applicator Essential!
        
You will need 1 package(s).
1 package = 1 Tube.

                $7.29
            
             / Package | SKU: XTL-1001