Retired - Pumpkin Patch Necklace

PROJECT N189
Designer: Andrea Morici
Skill Level: Beginner
Adorable little carved Carnelian pumpkins with vine tendrils made from antiqued brass wire are clustered together to create the pendant for this unique fall necklace.
Instructions

Note: Components and tools listed within this INSTRUCTIONS box and the printer-friendly PDF, if available, may have been discontinued since this project was published. Refer to the PURCHASE COMPONENTS and TOOLS AND OTHER SUPPLIES sections for current availability.

  1. Onto onto a headpin thread an antiqued brass bead cap and a carnelian pumpkin. Create a wrapped wire loop, but instead of trimming off the excess wire, use your round nose pliers (XTL-5060) to curl the wire into a spiral shape. Make five more of these pumpkin dangles (for a total of six) and set them aside.
  2. Onto two headpins, thread an antiqued brass bead cap and a 6mm carnelian bead. Onto two more headpins, thread an antiqued brass bead cap and a fluted antiqued brass bead. Create a wrapped wire loop on all four of these headpins and trim off excess wire.
  3. Cut a piece of chain two and a half inches long. Open ten 5.25mm jump rings. Thread each of the jump rings through each of the headpin dangles that you have just created. Thread the jump rings through random links on the length of chain, making sure the headpin dangles are spaced evenly apart. Leave the very top link empty. Close all jump rings once more.
  4. Open a 7.25mm jump ring and thread it through the top link of the chain. Before you close the jump ring, thread it through the loop half of the toggle clasp. After you have done this, close the jump ring again.
  5. Cut a length of Soft Flex antique brass colored beading wire at about two feet long. Secure one end of the wire with a Bead Stopper (XTL-3000).
  6. Onto the beading wire, thread alternating 6mm carnelian round beads and 6mm antiqued brass fluted beads until you reach your desired length. This part of our necklace is roughly sixteen and a half inches long.
  7. Onto the end of the strand thread a crimp bead, but do not crimp it yet. Thread the wire through the small loop on the toggle bar part of the clasp and back through the crimp tube and several consecutive beads. Pull the wire snug, but not too tight, and crimp the tube. Trim off excess wire.
  8. Remove the Bead Stopper from the other side of the strand. Onto the end of the strand thread a crimp bead, but do not crimp it yet. Thread the wire through the small loop on round part of the toggle clasp and back through the crimp tube and several consecutive beads. Pull the wire snug, but not too tight, and crimp the tube. Trim off excess wire.
WHAT YOU'LL NEED: (scroll down for purchase options)
  • CHA-7190 - Vintaj Natural Brass 3.5mm Round Rolo Chain - Bulk By The Foot
    Project uses 1 foot. You will need 1 package.

  • SPCA-57 -
    Project uses 6 pieces. You will need 1 package.

  • SPCA-36 - Red Carnelian Gemstone 6mm Round Beads / 15.5 In. Strand
    Project uses 38 pieces. You will need 1 package.

  • BMB-7051 - Antiqued Brass Openwork Beaded Daisy Bead Caps 1.3mm x 6mm (50)
    Project uses 10 pieces. You will need 1 package.

  • BMB-5174 - Antiqued Brass Balloon 6mm Round Beads (100)
    Project uses 39 pieces. You will need 1 package.

  • FJR-5352 - Vintaj Natural Brass Jump Rings 5.25mm Open 18 Gauge (20)
    Project uses 9 pieces. You will need 1 package.

  • FJR-5372 - Vintaj Natural Brass Jump Rings 7.25mm Open 16 Gauge (20)
    Project uses 1 piece. You will need 1 package.

  • FCR-1252 - Economy Brass Crimp Beads 2mm x 1.5mm (x100)
    Project uses 2 pieces. You will need 1 package.

  • FCL-4700 - Antiqued Brass Flower Toggle Clasps 14mm (4 Sets)
    Project uses 1 piece. You will need 1 package.

  • FHP-5537 - Vintaj Natural Brass Fine Head Pins For Pearls 24 Gauge 2.5 Inch (20)
    Project uses 10 pieces. You will need 1 package.

RECOMMENDED TOOLS:
  • XTL-3000 - Bead Stopper- Stop Beads Sliding Off Stringing Material
Additional Information
Theme Halloween, Autumn
Ingredients BMB-7051, FJR-5352, FJR-5372, FCR-1252, FCL-4700, FHP-5537,

Purchase Components

Purchase the components needed to make this project. Change quantities as needed to make multiple pieces. This project is RETIRED. Please review project instructions carefully—some items may no longer be available for this project and will not be listed below. Tip: Save this project to your wishlist to easily return to project instructions.
Antiqued Brass Openwork Beaded Daisy Bead Caps 1.3mm x 6mm (50 pcs)
You will need 1 package(s).
1 package = 50 Pieces.
$4.87 / Package | SKU: BMB-7051
Vintaj Natural Brass Jump Rings 5.25mm Open 18 Gauge (20 Pieces)
You will need 1 package(s).
1 package = 20 Pieces.
$2.69 / Package | SKU: FJR-5352
Vintaj Natural Brass Jump Rings 7.25mm Open 16 Gauge (20 Pieces)
You will need 1 package(s).
1 package = 20 Pieces.
$3.19 / Package | SKU: FJR-5372
Crimp Beads, Barrel 2x1.5mm, Brass (100 Pieces)
You will need 1 package(s).
1 package = 100 Pieces.
$2.69 / Package | SKU: FCR-1252
You will need 1 package(s).
1 package = .
/ Package | SKU: FCL-4700
Vintaj Natural Brass Head Pin, 2.5 Inches Long and 24 Gauge Thick (20 Pieces)
You will need 1 package(s).
1 package = 20 Pieces.
$2.79 / Package | SKU: FHP-5537
Earn Reward Points Earn Reward Points with your purchase of project components or tools.

Tools and Other Supplies:

Featured New Video [VIEW ALL VIDEOS]

Accessible Options For closed captions/subtitles, click the CC icon on the video player after starting the video.

You recently viewed

Clear recently viewed