Retired - Emily Choker

Note: Components and tools listed within this INSTRUCTIONS box and the printer-friendly PDF, if available, may have been discontinued since this project was published. Refer to the PURCHASE COMPONENTS and TOOLS AND OTHER SUPPLIES sections for current availability.

1. Cut off two lengths of beading wire, 20 inches each.
2. Place a bead stopper over both wires, about two inches from one end.
3. For this project you will be stringing both wires simultaneously. Lay them out in front of you so that one is on "top".
4. To both wires, string on one spacer bar.
5. To the top wire, string four 6mm pearls. To the bottom wire, string three 8mm pearls.
6. To both wires, string on one spacer bar.
7. To the top wire, string four 6mm pearls. To the bottom wire, string three 8mm pearls.
8. To both wires, string on one spacer bar.
9. To the top wire, string five 6mm pearls. To the bottom wire, string four 8mm pearls.
10. To both wires, string on one spacer bar.
11. To the top wire, string five 6mm pearls. To the bottom wire, string four 8mm pearls.
12. To both wires, string on one spacer bar.
13. To the top wire, string four 6mm pearls. To the bottom wire, string three 8mm pearls.
14. To both wires, string on one spacer bar.
15. To the top wire, string four 6mm pearls. To the bottom wire, string three 8mm pearls.
16. To the top wire, string three 6mm pearls. To the bottom wire, string three 8mm pearls.
17. To both wires, string on one spacer bar.
18. Now you will repeat in reverse order on the other side of the necklace.
19. After ending with one spacer bar, place one crimp bead on to each wire. Thread the wire up through one loop of one end of the clasp and back down through the crimp bead. Crimp the crimp bead. Snip any excess wire. Use a crimp cover over the crimp bead. Repeat for the other wire on this side.
20. Move to the starting end, remove the bead stopper and repeat the above process for the crimp beads and covers.
21. All done!

• BCP-12106 - Dazzle It! Czech Glass Pearls, 8mm Round, 1 Strand, Rose Gold
  Project uses 46 pieces. You will need 3 packages.


• BCP-12082 - Dazzle It! Czech Glass Pearls, 6mm Round, 1 Strand, Rose Gold
  Project uses 58 pieces. You will need 2 packages.


• FCO-1211 - 22K Gold Plated 8mm Bead Double Strand Spacer Bar 11.5mm Long (20)
  Project uses 15 pieces. You will need 1 package.


• FCR-1056 - Bright Gold Tone Crimp Bead Covers 3mm (144)
  Project uses 4 pieces. You will need 1 package.


• FCR-1258 - 22K Gold Plated Crimp Beads 1.8 x 1.5mm (144)
  Project uses 4 pieces. You will need 1 package.


• FCL-4800 - 23K Gold Plated 2-Strand Box Clasp With Austrian crystal 22x12mm (1)
  Project uses 1 piece. You will need 1 package.


• XCR-5143 - Soft Flex, 21 Strand Fine Beading Wire .014 Inch Thick, 30 Feet, Satin Silver
  Project uses 40 Inches. You will need 1 package.

• XTL-3000 - Bead Stopper- Stop Beads Sliding Off Stringing Material
• XTL-5600 - Xuron Sharp Flush Cutter Pliers - Wire/Soft Flex
• XTL-5608 - Xuron 4 In 1 Crimping Pliers - Works On 1, 2 And 3mm Crimps!