Retired - Olivia Bracelet

PROJECT B3030
Designer: Karlin Jones
Skill Level: Beginner
Created using a combination of green opal cup chain, gold plated findings and two flower stampings by Nunn Design, this bracelet offers a classic style with a bit of old world charm.
Instructions

Note: Components and tools listed within this INSTRUCTIONS box and the printer-friendly PDF, if available, may have been discontinued since this project was published. Refer to the PURCHASE COMPONENTS and TOOLS AND OTHER SUPPLIES sections for current availability.

This bracelet measures approximately 7� long. To adjust the length, simply add more or less chain.
  1. Begin by cutting a 7� length of chain with your flush cutters. Set aside.
  2. Cut a 7� length of your cup chain. Set aside.
  3. Cut a length of cup chain that is 12 rhinestone links long. Set aside.
  4. Take your large Nunn Design flower stamping and add a dab of E-6000 glue onto the center. Take your smaller flower stamping and place it on top of the glue (flat side down) and gently press down. Set aside to dry for a few minutes.
  5. Take your bail, flip it over (to the flat side) and add a dab of E6000 glue onto the back. Flip over your large Nunn Design flower stamping (once its dry) and glue your bail onto the back. Make sure that the loop from your bail is peeking out (so you can add a jump ring through it later). Set aside to dry for a few minutes.
  6. Once your bail is securely glued onto your flower stamping, flip it over and carefully add a thin line of E-6000 glue onto the large flower stamping, right around the outer edges of the smaller flower stamping. Take your short cup chain length and carefully line it on top of the glue, going in a circular motion. Set aside to dry.
  7. Next, watch the video on How to Use Cup Chain Ends.
  8. Take your cup chain length and following what you learned in the video, add a cup chain end onto each end of your cup chain length, using your chain nose pliers.
  9. Next, open up a jump ring and slide on the loop from one half of your clasp set, the loop from a cup chain end from one side of your cup chain length and the last link from one side of your gold plated chain.
  10. Before closing up that jump ring, slide on a second jump ring, then close. Open up the second jump ring and onto it add the loop from your bail. Close the jump ring with your pliers.
  11. Now go to the other side of your chain lengths. Open another jump ring and slide on the loop from the cup chain end, the last link from that side of your gold plated chain and the loop from the that half of your clasp set. Close the jump ring.
  12. Your bracelet is done.
WHAT YOU'LL NEED: (scroll down for purchase options)
  • CHA-9802 - Nunn Design Antiqued Gold Plated Textured Cable Chain By The Foot
    Project uses 7 inches. You will need 1 package.

  • CHA-10131 - Czech Crystal Brass Rhinestone Cup Chain 18PP Green Opal (By The Foot)
    Project uses 7 inches. You will need 1 package.

  • FCL-6682 - 22K Gold Plated Magnetic Clasps 6mm x 8mm (3)
    Project uses 1 set. You will need 1 package.

  • FCR-8007 - Raw Brass Foldover 18PP Cup Chain Crimp On Ends For Cup Chain (20 Pieces)
    Project uses 2 pieces. You will need 1 package.

  • PND-6856 - Nunn Design Solid Brass Stamping Small Marigold Flower Embellishment 8mm (4)
    Project uses 1 piece. You will need 1 package.

  • PND-6854 - Nunn Design Solid Brass Stamping Large Marigold Flower Embellishment 22mm (1)
    Project uses 1 piece. You will need 1 package.

  • FCO-4250 - TierraCast 22K Gold Plated Pewter Stone Mounting Bail For Cabochon (2)
    Project uses 1 piece. You will need 1 package.

  • FJR-5250 - 22K Gold Plated Open Jump Rings 5mm 20 Gauge (100)
    Project uses 3 pieces. You will need 1 package.

  • XTL-1054 - E6000 Industrial Strength Glue Adhesive (0.18 fl oz)
    Project uses 1 piece. You will need 1 package.

RECOMMENDED TOOLS:
  • XTL-5600 - Xuron Sharp Flush Cutter Pliers - Wire/Soft Flex
  • XTL-5511 - Beadsmith Jeweller's Micro Pliers Chain Nose Flat Nose
Additional Information
Theme Summer, Spring, Autumn
Ingredients CHA-9802, FCL-6682, FJR-5250, XTL-1054,

Purchase Components

Purchase the components needed to make this project. Change quantities as needed to make multiple pieces. This project is RETIRED. Please review project instructions carefully—some items may no longer be available for this project and will not be listed below. Tip: Save this project to your wishlist to easily return to project instructions.
Nunn Design Antiqued Gold Plated Textured Cable Chain 9mm, by the Foot
You will need 1 package(s).
1 package = By the Foot.
$6.89 / Package | SKU: CHA-9802
Magnetic Clasps, Round 8x6mm 22K Gold Plated (3 Set)
You will need 1 package(s).
1 package = 3 Sets.
$10.15 / Package | SKU: FCL-6682
22K Gold Plated Open Jump Rings 5mm 20 Gauge (100 pcs)
You will need 1 package(s).
1 package = 100 Pieces.
$4.94 / Package | SKU: FJR-5250
E6000 Industrial Strength Glue Adhesive (0.18 fl oz)
You will need 1 package(s).
1 package = 1 Piece.
$2.19 / Package | SKU: XTL-1054
Earn Reward Points Earn Reward Points with your purchase of project components or tools.

Tools and Other Supplies:

The Beadsmith Jeweller's Micro Pliers Chain Nose Flat Nose

Related Video [VIEW ALL VIDEOS]

Accessible Options For closed captions/subtitles, click the CC icon on the video player after starting the video.

You recently viewed

Clear recently viewed