Retired - Blue Jay Way Bracelet

PROJECT B125
Designer: Andrea Morici
Skill Level: Intermediate
This handsome little Blue Jay sits perched upon your wrist, amidst a pretty variety of crystals and glass druks.
Instructions

Note: Components and tools listed within this INSTRUCTIONS box and the printer-friendly PDF, if available, may have been discontinued since this project was published. Refer to the PURCHASE COMPONENTS and TOOLS AND OTHER SUPPLIES sections for current availability.

  1. Follow the directions on the back of the transfer sheet package in order to place the Blue Jay image on the blank bracelet panel. Once the image has dried, coat it with a thin layer of Mod Podge. Set the bracelet aside to dry.
  2. Cut thirty-two pieces of wire at two inches long, and create a simple wire loop at one end of each, essentially turning them into eyepins.
  3. Thread each of the Austrian crystals and the Druks onto each of the eyepins, create a simple wire loop on each, and trim off excess wire.
  4. To create the "chain" part of the bracelet, link the bead segments together by opening a loop at one end of a segment the way you would open a jump ring and threading through a loop at one end of another bead segment before closing the loop again.
  5. Create six bead segment chains using this method, four with all druks in alternating colors, and two containing three various Austrian crystal beads, with a single druk in between each.
  6. Attach the chains to the bracelet panel and the the three strand reducer using oval jump rings. There should be three chains on either side of the bracelet, all druks on top and bottom, and the Austrian crystal chain in the middle.
  7. Thread the two Czech glass flower bead caps onto the two headpins. Create a simple loop on each and trim off excess wire.
  8. Open each of the loops on the flowers, and add one to the hole on one side of the bracelet panel, the other flower to the hole on the other side of the bracelet panel.
  9. Use an oval jump ring to attach the lobster clasp to one end of the bracelet and the extender chain to the other end.
Keywords:blue jay, bird, transfer sheet, leaves, spring, btq-natureWHAT YOU'LL NEED: (scroll down for purchase options)
  • FCO-7013 - Antiqued Silver Plated Blank Curved Rectangle Connector Panel For Bracelet 45mm (1)
    Project uses 1 piece. You will need 1 package.

  • XTL-1041 - Mod Podge Gloss All-In-One Decoupage Sealer / Glue / Finish (4 fl. oz. )
    Project uses 1 piece. You will need 1 package.

  • XTL-9511 - Nunn Design Transfer Sheet Butterflies & Birds For Scrapbook -Fits Patera
    Project uses 1 piece. You will need 1 package.

  • AXC-2730 - Beadalon Silver Plated Chain Necklace Extender W/ Heart 2 Inch (10)
    Project uses 1 piece. You will need 1 package.

  • FCL-2513 - Beautiful Silver Plated Curved Lobster Clasps 10mm (10)
    Project uses 1 piece. You will need 1 package.

  • WNT-2030 - Beadsmith Tarnish Resistant Silver Color Copper Wire 20 Gauge 15 Yards (13.5 Meters)
    Project uses 64 inches. You will need 1 package.

  • FJR-5400 - TierraCast Silver Plated Brass Oval Jump Rings 4mm 20 Gauge (50)
    Project uses 12 pieces. You will need 1 package.

  • FHP-3001 - Silver Plated 2mm Ball Head Pins 21 Gauge 1.5 Inch (20)
    Project uses 2 pieces. You will need 1 package.

  • SWBB-1833 - Austrian Crystal, 5328 Bicone Beads 8mm, 8 Pieces, Montana
    Project uses 2 pieces. You will need 1 package.

  • SWC-0843 - Austrian Crystal, 5000 Round Beads 8mm, 8 Pieces, Olivine AB
    Project uses 2 pieces. You will need 1 package.

  • BCP-7447 -
    Project uses 10 pieces. You will need 1 package.

  • BCP-7478 - Czech Glass Druk Round 4mm 'Olivine Ghost Matte AB' (100 Beads)
    Project uses 8 pieces. You will need 1 package.

  • BCP-7456 - Czech Glass Druk Round 4mm 'Montana Ghost Matte AB' (100 Beads)
    Project uses 10 pieces. You will need 1 package.

Additional Information
Ingredients XTL-1041, AXC-2730, FCL-2513, WNT-2030, FJR-5400, FHP-3001,

Purchase Components

Purchase the components needed to make this project. Change quantities as needed to make multiple pieces. This project is RETIRED. Please review project instructions carefully—some items may no longer be available for this project and will not be listed below. Tip: Save this project to your wishlist to easily return to project instructions.
Mod Podge Gloss All-In-One Decoupage Sealer / Glue / Finish (4 fl. oz. )
You will need 1 package(s).
1 package = 4 fl. oz..
$6.89 / Package | SKU: XTL-1041
Necklace Chain Extender, 3.5mm Curb Links with Heart 2 Inches, Silver Plated (10 Pieces)
You will need 1 package(s).
1 package = 10 Pieces.
$2.49 / Package | SKU: AXC-2730
Lobster Clasps, Curved 12.5mm, Silver Plated (10 Pieces)
You will need 1 package(s).
1 package = 10 Pieces.
$8.29 / Package | SKU: FCL-2513
Wire Elements, Tarnish Resistant Silver Color Copper Wire, 20 Gauge 15 Yards (13.5 Meters)
You will need 1 package(s).
1 package = 1 Spool.
$9.99 / Package | SKU: WNT-2030
You will need 1 package(s).
1 package = .
/ Package | SKU: FJR-5400
Head Pins, with Ball Head 1.5 Inches Long and 21 Gauge Thick, Silver Plated (20 Pieces)
You will need 1 package(s).
1 package = 20 Pieces.
$2.39 / Package | SKU: FHP-3001
Earn Reward Points Earn Reward Points with your purchase of project components or tools.

Tools and Other Supplies:

Featured New Video [VIEW ALL VIDEOS]

Accessible Options For closed captions/subtitles, click the CC icon on the video player after starting the video.

You recently viewed

Clear recently viewed