Retired - The Disco Earrings

PROJECT E111
Designer: Andrea Morici
Skill Level: Beginner
No dancing outfit would be complete without our Disco Necklace and its perfect mate: this spectacular pair of earrings.
Instructions

Note: Components and tools listed within this INSTRUCTIONS box and the printer-friendly PDF, if available, may have been discontinued since this project was published. Refer to the PURCHASE COMPONENTS and TOOLS AND OTHER SUPPLIES sections for current availability.

Remember to double everything the instructions call for to make both earrings! Begin by threading the following on to a head pin: a fire polish beadan 8mm sparkle beadanother fire polish beada tube beadanother fire polish bead. Create a simple loop and trim off excess.Thread the following on to two more headpins: a fire polish beada sparkle crimp bead covera tube beadanother fire polish bead.Create a simple loop and trim off excess.Gently open the loop at the top of each headpin, add a closed jump ring to each, and close again.Thread a tube bead on to an eyepin and create a simple loop.Cut two pieces of chain that are about an inch and an eighth (3 large links) long.Add one end of each piece of chain to either loop on the eyepin.Gather both ends of the chain and add them both to a single jump ring, and add that jump ring to the loop on the earring hook.Cut about a foot of Artistic craft wire and insert roughly an eighth of an inch of the end of the wire into one end of the tube bead on the eyepin.Wrap the wire three times tightly and closely around the tube bead, thread the wire though the closed jump ring at the end of one of the shorter headpin dangles ensuring that it is wrapped tightly against the bottom of the horizontal tube. Continue wrapping the wire six times tightly around the tube, then add the long dangle the same way you added the first one.Continue wrapping the wire six times tightly around the tube, and add the final dangle the same way you added the first two.Finally, wrap the wire tightly around the tube three more times. Trim off excess wire, save for about a quarter inch, which you will insert into the end of the tube, or if that is not possible, wrap the excess tightly around the loop of the eyepin against the end of the tube.Make sure that the dangles are evenly spaced from each other, and have the same spacing on both earrings.Tip: Check package quantities for each component. You may have extra material to make more than one finished project, or will have leftovers for other projects. In some cases, adding on just one more package of a component may be all you need to make multiple pieces.All designs © Beadaholique Inc.
WHAT YOU'LL NEED: (scroll down for purchase options)
  • BMB-6686 - Silver Plated Brushed Satin Tube Beads 24-27mm (10)
    Project uses 8 pieces. You will need 1 package.

  • BCP-3394 - Czech Fire Polished Glass Beads 3mm Round Matte Jet Black (50)
    Project uses 14 pieces. You will need 1 package.

  • BMB-1808 - Silver Plated Stardust Sparkle Round Beads 8mm (25)
    Project uses 2 pieces. You will need 1 package.

  • FCR-1070 - Silver Plated Stardust Sparkle Crimp Bead Covers 4mm (144)
    Project uses 4 pieces. You will need 1 package.

  • FHP-5325 - Silver Plated Head Pins 2 Inches/21 Gauge (X50)
    Project uses 6 pieces. You will need 1 package.

  • FHP-6260 - Silver Plated Open Eye Pins 21 Gauge 1.5 Inch (x50)
    Project uses 2 pieces. You will need 1 package.

  • FEA-2010 - Sterling Silver French Wire Earring Hooks (10)
    Project uses 2 pieces. You will need 1 package.

  • FJR-4005 - Silver Plated Closed Jump Rings 5mm 20 Gauge (50)
    Project uses 6 pieces. You will need 1 package.

  • WCR-2630 - Artistic Wire, Silver Plated Craft Wire 26 Gauge Thick, 15 Yard Spool, Tarnish Resistant Silver
    Project uses 2 pieces. You will need 1 package.

  • CHA-9804 - Nunn Design Silver Plated Textured Cable Chain 4mm By The Ft
    Project uses 1 foot. You will need 1 package.

Additional Information
Ingredients BCP-3394, FCR-1070, FHP-5325, FHP-6260, FEA-2010, FJR-4005, WCR-2630, CHA-9804,

Purchase Components

Purchase the components needed to make this project. Change quantities as needed to make multiple pieces. This project is RETIRED. Please review project instructions carefully—some items may no longer be available for this project and will not be listed below. Tip: Save this project to your wishlist to easily return to project instructions.
Czech Fire Polished Glass Beads 3mm Round Matte Jet Black (50 pcs)
You will need 1 package(s).
1 package = 50 Pieces.
$1.49 / Package | SKU: BCP-3394
Crimp Bead Covers, Stardust Sparkle 4mm, Silver Plated (144 Pieces)
You will need 1 package(s).
1 package = 144 Pieces.
$12.99 / Package | SKU: FCR-1070
Head Pins, 2 Inches Long and 21 Gauge Thick, Silver Plated (50 Pieces)
You will need 1 package(s).
1 package = 50 Pieces.
$4.05 / Package | SKU: FHP-5325
Open Eye Pins, 1.5 Inches Long and 21 Gauge Thick Silver Plated (50 Pieces)
You will need 1 package(s).
1 package = 50 Pieces.
$3.85 / Package | SKU: FHP-6260
Earring Findings, French Ear Wire Hook 16mm Long 21 Gauge, Sterling Silver (10 pcs)
You will need 1 package(s).
1 package = 5 Pairs.
$8.67 / Package | SKU: FEA-2010
Jump Rings, Closed 5mm Diameter 20 Gauge, Silver Plated (20 Pieces)
You will need 1 package(s).
1 package = 50 Pieces.
$7.39 / Package | SKU: FJR-4005
Artistic Wire, Silver Plated Craft Wire 26 Gauge Thick, Tarnish Resistant Silver (15 Yard Spool)
You will need 1 package(s).
1 package = 1 Spool.
$7.49 / Package | SKU: WCR-2630
Nunn Design Silver Plated Textured Cable Chain, 4mm, by the Foot
You will need 1 package(s).
1 package = By the Foot.
$6.09 / Package | SKU: CHA-9804
Earn Reward Points Earn Reward Points with your purchase of project components or tools.

Tools and Other Supplies:

Featured New Video [VIEW ALL VIDEOS]

Accessible Options For closed captions/subtitles, click the CC icon on the video player after starting the video.

You recently viewed

Clear recently viewed