Retired - Pink Floral Parade Necklace

PROJECT N2031
Designer: Kat Silvia
Skill Level: Intermediate
Strung together, these beautiful, coral pink 2-holed dagger beads make a wonderful center piece of pinwheel-like flowers.
Instructions

Note: Components and tools listed within this INSTRUCTIONS box and the printer-friendly PDF, if available, may have been discontinued since this project was published. Refer to the PURCHASE COMPONENTS and TOOLS AND OTHER SUPPLIES sections for current availability.

This finished necklace is 20.5 inches in length.
  1. Begin by cutting about 2 feet of beading thread. Thread your needle and place a bead stopper about 6 inches from the end. Pick up two seed beads and one dagger bead by the second hole (the hole closest to the center of the bead). Pick up two more seed beads and another dagger bead by the second hole. Continue until you have 10 dagger beads total. Remove your needle and place a bead stopper on your thread end.
  2. Place a needle on another 2 feet of beading thread, and this time pickup one seed bead and go back through the top hole of the string of daggers that you just strung. Continue by picking up a single seed bead in between each top hole of each dagger.
  3. Once you have gotten to the end, take the thread that is going through the top hole of the daggers and string it back thru that first seed bead you started with in the previous step. Work your beading thread through the thread path in the circle until the thread ends meet up with each other, pull them snug to close your circle and tie an overhand double knot. Work some of each thread tail back into your circle and then trim the ends with your thread zapper.
  4. Repeat this process with the thread that is going through the two seed beads and the second hole on the daggers (remove the bead stoppers first). Trim the ends
  5. Repeat the above process twice more, so you have three "flowers" total.
  6. Cut a piece of chain that is 3 inches. Loop it around two flowers, by going though the center circles of the bead woven flowers. Connect the ends of this chain by opening a jump ring and closing it around the two end links of this chain.
  7. Repeat this last step to attach the third flower in the same way. You now have the 3 flowers linked together (see photo).
  8. Cut a piece of chain that is 16 inches. Thread this chain through the center circle of one of the end flowers and then loop it around to form a double chain. Open a jump ring and attach it to both ends of this chain, close the jump ring. On to this jump ring, attach another jump ring. And add a third jump ring to that last one. To that final jump ring, attach a lobster clasp.
  9. Repeat the previous step for the other side. However, add one more jump ring, for a total of four to the ends of the chain.
WHAT YOU'LL NEED: (scroll down for purchase options)
  • BCP-10281 -
    Project uses 30 pieces. You will need 1 package.

  • BCS-1410 - Czech Seed Beads 11/0 Light Rose Silver Foil Lined (1 Hank)
    Project uses 90 pieces. You will need 1 package.

  • CHA-9953 - Silver Plated Round Rolo Chain 3.7mm Bulk By The Foot
    Project uses 38 inches. You will need 4 packages.

  • FJR-5150 - Silver Plated Open Jump Rings 5mm 20 Gauge (x100)
    Project uses 7 pieces. You will need 1 package.

  • FCL-2513 - Beautiful Silver Plated Curved Lobster Clasps 10mm (10)
    Project uses 1 piece. You will need 1 package.

  • XCR-1278 - FireLine Braided Beading Thread, 6lb Test and 0.006 Thick, 50 Yards, Crystal Clear
    Project uses 1 spool. You will need 1 package.

RECOMMENDED TOOLS:
  • XTL-3000 - Bead Stopper- Stop Beads Sliding Off Stringing Material
  • XTL-3006 - Beadsmith English Beading Needles Size 12 (4 Needles)
  • XTL-0106 - BeadSmith Cordless Thread Zap II Thread Burner Tool
Additional Information
Theme Spring, Easter, As Seen In
Ingredients BCS-1410, CHA-9953, FJR-5150, FCL-2513, XCR-1278,

Purchase Components

Purchase the components needed to make this project. Change quantities as needed to make multiple pieces. This project is RETIRED. Please review project instructions carefully—some items may no longer be available for this project and will not be listed below. Tip: Save this project to your wishlist to easily return to project instructions.
Czech Glass Seed Beads, 11/0 Round, 1 Hank, Light Rose Silver Foil Lined
You will need 1 package(s).
1 package = 1 Hank.
$7.59 / Package | SKU: BCS-1410
Silver Plated Rolo Chain, 3.7mm, by the Foot
You will need 4 package(s).
1 package = By the Foot.
$3.85 / Package | SKU: CHA-9953
Silver Plated Open Jump Rings 5mm 20 Gauge (100 pcs)
You will need 1 package(s).
1 package = 100 Pieces.
$3.27 / Package | SKU: FJR-5150
Lobster Clasps, Curved 12.5mm, Silver Plated (10 Pieces)
You will need 1 package(s).
1 package = 10 Pieces.
$8.29 / Package | SKU: FCL-2513
FireLine Braided Beading Thread, 6lb Test and 0.006 Thick, Crystal Clear (50 Yards)
You will need 1 package(s).
1 package = 1 Spool.
$11.15 / Package | SKU: XCR-1278
Earn Reward Points Earn Reward Points with your purchase of project components or tools.

Tools and Other Supplies:

The Beadsmith English Beading Needles Size 12 (4 pcs)
The Beadsmith Cordless Thread Zap II Thread Burner Tool

Related Video [VIEW ALL VIDEOS]

Accessible Options For closed captions/subtitles, click the CC icon on the video player after starting the video.

You recently viewed

Clear recently viewed