Retired - Headliner Wrap Bracelet in Black

PROJECT B2236
Designer: Kat Silvia
Skill Level: Intermediate
This personalized bracelet is guaranteed to get you festival ready to rock on and sing your heart out at your next music concert.
Instructions

Note: Components and tools listed within this INSTRUCTIONS box and the printer-friendly PDF, if available, may have been discontinued since this project was published. Refer to the PURCHASE COMPONENTS and TOOLS AND OTHER SUPPLIES sections for current availability.

These instructions will give you a wrap bracelet that is 6.5 inches. To adjust the length, modify the length of the leather cord and chain accordingly.
  1. Please watch our video: How to Use the Vintaj BIGkick with Etching and Embossing Dies.
  2. From what you learned in the video, place the guitar pick stamping into the die. Choose the section of the die that you would like to emboss on the guitar pick. I used a section just above center of the die (see photo for reference).
  3. Run it through the machine. Remove the stamping from the die.
  4. Use the Vintaj Relief Block on both sides of the stamping to bring out the shiny brass.
  5. To make the letters you will repeat the above process. I have used three blanks, but you can use all six or purchase additional blanks for you words or name.
  6. Next, using a paint brush dab on Vintaj Patina to the front of the guitar pick stamping. Quickly wipe off any excess with a paper towel. You may add more or less patina to achieve your desired effect. Repeat on the other side of the patina. I used fire opal on half and onyx on the other half. I repeated this on both sides (see photo for reference).
  7. Cut off 14 inches of leather cord and 16 inches of chain. Thread the leather through the chain skipping every other chain link. Allow the chain to twist and curve with the leather.
  8. Take one headpin and string on one gemstone bead, make a simple wire loop. Repeat this step for three more gemstones.
  9. Attach the fold over cord ends to each end of the leather cord.
  10. Open the large jump ring that comes with the clasp and attach it to one end of the clasp, one end of the chain and the foldover cord end attached to the leather. Close the jump ring. Repeat this on the other side without attaching the clasp.
  11. Lay the bracelet out in front of you and moving from the left hand side using jump rings, move 2 inches and attach one gemstone simple wire loop to the chain.
  12. Move 1 inch and attach the guitar pick. Move 1/2 inch and attach another gemstone. Move 3 inches and attach a gemstone. Move 4 inches and attach the three blanks with the letters on. Attach them on every other link moving to the left (you may need to adjust this step if you have additional letters). Move another 1/2 inch and add the final gemstone bead.
WHAT YOU'LL NEED: (scroll down for purchase options)
  • CHA-10065 - Vintaj Natural Brass 8.5x6.5mm Slender Oval Chain - Sold By The Foot
    Project uses 16 Inches. You will need 2 packages.

  • PND-7371 - Vintaj Natural Brass Altered Blank Stamping Guitar Pick 31x26.5mm (2)
    Project uses 1 piece. You will need 1 package.

  • FJR-5352 - Vintaj Natural Brass Jump Rings 5.25mm Open 18 Gauge (20)
    Project uses 8 pieces. You will need 1 package.

  • CHY-2002 - Genuine Leather Cord, Round 2mm, By the Yard, Black
    Project uses 14 Inches. You will need 1 package.

  • PND-7067 - Vintaj Natural Brass Rustic Altered Blank Square Pendants 10mm (6)
    Project uses 3 pieces. You will need 1 package.

  • FHP-2720 - Vintaj Natural Brass, Paddle Head Pins 1 Inch Long 21 Gauge Thick, 12 Pieces
    Project uses 4 pieces. You will need 1 package.

  • FCR-1445 - Antiqued Brass Foldover 3mm Cord Ends For Ribbon
    Project uses 2 pieces. You will need 1 package.

  • SPHE-63 - Hematite Gemstone Beads, 8mm Faceted Round, 16 Inch, Metallic Rainbow
    Project uses 4 pieces. You will need 1 package.

  • FCL-9054 - Vintaj Natural Brass 13mm Bracelet Fold-Over Clasp / Jump Ring Set (2 Sets)
    Project uses 1 Set. You will need 1 package.

  • XTL-0403 - Vintaj Patina, Opaque Permanent Ink For Metal, 0.5 Ounce, Fire Opal
    Project uses 1 piece. You will need 1 package.

  • XTL-9078 - Vintaj Patina Opaque Permanent Ink - Black Onyx - 0.5 Ounce Bottle
    Project uses 1 piece. You will need 1 package.

RECOMMENDED TOOLS:
  • XTL-1200 - Sizzix BIGkick Die Cut Machine - Vintaj Special Edition - Cut, Emboss, And Etch!
  • XTL-09370 - Vintaj DecoEmboss Die, For Sizzix Bigkick Machine - Uppercase Typewriter
  • XTL-1243 - Vintaj DecoEmboss Die For Sizzix Bigkick Machine - India Archway
  • XTL-880 - ICE Resin, Angled Paint Brushes for ICED Enamels & Paper Sealant, 6 Pack
  • XTL-5260 - Beadsmith Fold Over Crimping Pliers For Leather & Suede Findings
  • XTL-5600 - Xuron Sharp Flush Cutter Pliers - Wire/Soft Flex
  • XTL-5511 - Beadsmith Jeweller's Micro Pliers Chain Nose Flat Nose
  • XTL-5514 - Beadsmith Jewelry Fine Round Nose Micro Pliers
Additional Information
Theme Summer, Personalization, Men's
Ingredients PND-7371, FJR-5352, CHY-2002, FHP-2720, FCR-1445, XTL-0403, XTL-9078,

Purchase Components

Purchase the components needed to make this project. Change quantities as needed to make multiple pieces. This project is RETIRED. Please review project instructions carefully—some items may no longer be available for this project and will not be listed below. Tip: Save this project to your wishlist to easily return to project instructions.
You will need 1 package(s).
1 package = .
/ Package | SKU: PND-7371
Vintaj Natural Brass Jump Rings 5.25mm Open 18 Gauge (20 Pieces)
You will need 1 package(s).
1 package = 20 Pieces.
$2.59 / Package | SKU: FJR-5352
Leather Cord, Round 2mm, Black, by Leather Cord USA (1 yard)
You will need 1 package(s).
1 package = 1 Yard.
$2.49 / Package | SKU: CHY-2002
Vintaj Natural Brass, Paddle Head Pins 1 Inch Long 21 Gauge Thick (12 Pieces)
You will need 1 package(s).
1 package = 12 Pieces.
$3.39 / Package | SKU: FHP-2720
Cord Ends, Foldover For 3mm Leather Cord, Antiqued Brass (50 Pieces)
You will need 1 package(s).
1 package = 50 Pieces.
$7.17 / Package | SKU: FCR-1445
Vintaj Patina, Opaque Permanent Ink For Metal, Fire Opal (0.5 Ounce)
You will need 1 package(s).
1 package = 1 Bottle.
$7.99 / Package | SKU: XTL-0403
Vintaj Patina Opaque Permanent Ink - Black Onyx - 0.5 Ounce Bottle
You will need 1 package(s).
1 package = 1 Bottle.
$8.49 / Package | SKU: XTL-9078
Earn Reward Points Earn Reward Points with your purchase of project components or tools.

Tools and Other Supplies:

The Beadsmith Jeweller's Micro Pliers Chain Nose Flat Nose
The Beadsmith Jewelry Fine Round Nose Micro Pliers
$6.29 / Package | SKU: XTL-5514

Related Video [VIEW ALL VIDEOS]

Accessible Options For closed captions/subtitles, click the CC icon on the video player after starting the video.

You recently viewed

Clear recently viewed