Retired - Cinderella's Necklace

PROJECT N3018
Designer: Karlin Jones
Skill Level: Beginner
Step into a fairy tale with this ornate filigree stamping and blue organza ribbon necklace. Adorned with 4 different colors of Austrian crystal flatback rhinestones, this pretty necklace is both fun to make and wear!
Instructions

Note: Components and tools listed within this INSTRUCTIONS box and the printer-friendly PDF, if available, may have been discontinued since this project was published. Refer to the PURCHASE COMPONENTS and TOOLS AND OTHER SUPPLIES sections for current availability.

Before you begin, watch the video on How to Use a Jewel Setter. You will also need a scrap piece of wire or glue applicator for this project.
  1. Begin by opening two jump rings using your chain nose pliers.
  2. Place your filigree stamping vertically, making sure there is a point at the top. Refer to the photo. Take your open jump rings and attach them onto the filigree openings at either side of the top design of the stamping.
  3. Open the clasp on your blue organza ribbon and string the non-lobster clasp side through the two jump rings. Pull one side of the ribbon until it reaches the other side. Close the clasp back up. Your stamping should be hanging off of your ribbon.
  4. Now you will begin decorating your filigree stamping with Austrian crystal flatback rhinestones.
  5. Before you begin adding your rhinestones, remember that you can place them in any design or pattern you like. To apply the crystals, place a dab of glue on your filigree where you want them, use your jewel setter tool to lift up the flatbacks and place onto your stamping. Use the pointy end of the jewel setter to make adjustments. Refer back to the video for additional assistance.
  6. I began by taking the 8 larger Austrian crystal flatbacks in Night Shade and Caribbean Opal and placed them in a circular pattern in the center of the filigree stamping, with 1 Caribbean Opal rhinestone in the center of the circle.
  7. Then around the edges of the stamping, I added 16 of the smaller rhinestone flatbacks in Light Turquoise and Sapphire (6 of each). I also added 8 within the circle pattern (4 of each). Please refer to the photo to emulate my exact design.
  8. Once you are done, set aside to dry for an hour. Then with your tweezers, remove any left over glue from your stamping (you can do this just by nudging the tip of your tweezers under where glue might have spilled over and pulling it off of the stamping. Only do this where there are big globs of extra glue, you might or might not have any depending upon how careful you were).
  9. Lastly, add the 12 Light Turquoise rhinestones to your blue ribbon. You will add these the same way you added them to the filigree. Refer to the photo for the exact design.
  10. Your necklace is now ready.
WHAT YOU'LL NEED: (scroll down for purchase options)
  • XCR-4460 - Blue Organza Ribbon Necklace 17 Inch W/ Sterling Silver Clasp
    Project uses 1 piece. You will need 1 package.

  • PND-5716 - Antiqued Silver Plated Ornate Full Poppy Filigree Stamping 59mm (1)
    Project uses 1 piece. You will need 1 package.

  • SWF-407321 - Austrian Crystal, Round Flatback Rhinestone SS7 2.2mm, 72 Pieces, Light Turquoise
    Project uses 18 pieces. You will need 1 package.

  • SWF-13425 - Austrian Crystal, Round Flatback Rhinestone SS34 7mm, 12 Pieces, Caribbean Blue Opal
    Project uses 5 pieces. You will need 1 package.

  • SWF-41631 - Austrian Crystal, Round Flatback Rhinestone SS16 3.8mm, 50 Pieces, Sapphire
    Project uses 12 pieces. You will need 1 package.

  • SWF-140998 - Austrian Crystal, Round Flatback Rhinestone SS40 8.5mm, 8 Pieces, Crystal Silver Night
    Project uses 4 pieces. You will need 1 package.

  • FJR-3094 - Antiqued Silver Plated Open Jump Rings 6mm 18 Gauge (50)
    Project uses 2 pieces. You will need 1 package.

  • XTL-1054 - E6000 Industrial Strength Glue Adhesive (0.18 fl oz)
    Project uses 1 tube. You will need 1 package.

RECOMMENDED TOOLS:
  • XTL-1501 - Beadsmith Perfect Positioner / Jewel Setter Tool for Austrian crystal Flatback Rhinestones
  • XTL-5511 - Beadsmith Jeweller's Micro Pliers Chain Nose Flat Nose
  • XTL-4000 - Beadsmith Bead And Pearl Knotting Tweezers
Additional Information
Theme Vintage Look
Ingredients FJR-3094, XTL-1054,

Purchase Components

Purchase the components needed to make this project. Change quantities as needed to make multiple pieces. This project is RETIRED. Please review project instructions carefully—some items may no longer be available for this project and will not be listed below. Tip: Save this project to your wishlist to easily return to project instructions.
Antiqued Silver Plated Open Jump Rings 6mm 18 Gauge, (50 Pieces)
You will need 1 package(s).
1 package = Each.
$2.39 / Package | SKU: FJR-3094
E6000 Industrial Strength Glue Adhesive (0.18 fl oz)
You will need 1 package(s).
1 package = 1 Piece.
$2.09 / Package | SKU: XTL-1054
Earn Reward Points Earn Reward Points with your purchase of project components or tools.

Tools and Other Supplies:

The Beadsmith Jeweller's Micro Pliers Chain Nose Flat Nose
The Beadsmith Bead And Pearl Knotting Tweezers
$2.79 / Package | SKU: XTL-4000

Related Video [VIEW ALL VIDEOS]

Accessible Options For closed captions/subtitles, click the CC icon on the video player after starting the video.

You recently viewed

Clear recently viewed